OMAP-L138/AM-1808/AM-1810 initialization passed!
Configuring 128MB mDDR
                      Booting TI User Boot Loader
        UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53
        UBL Flashtype: SPI
Starting SPI Memory Copy...
Valid magicnum, 0x55424CBB, found at offset 0x00010000.
   DONE
Jumping to entry point at 0xC1080000.


U-Boot 2009.11 (Jan 13 2014 - 11:14:02)

I2C:   ready
DRAM:  128 MB
NAND:  256 MiB
MMC:   davinci: 0
In:    serial
Out:   serial
Err:   serial
ARM    Clock : 300000000 Hz
DDR    Clock : 150000000 Hz
EMIFA  CLock : 100000000 Hz
DSP    Clock : 300000000 Hz
ASYNC3 Clock : 150000000 Hz
Enet  config : 2
MMC 0 Enable : 0
Resetting ethernet phy
Net:   Ethernet PHY: GENERIC @ 0x03 [0x8]

Hit any key to stop autoboot:  0
U-Boot > print bootargs
bootargs=mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw rootwait
U-Boot > set ipaddr 169.254.60.80
U-Boot > set serverip 169.254.68.150
U-Boot > set gatewayip 169.254.1.1
U-Boot > set netmask 255.255.255.0
U-Boot > saveenv
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
U-Boot > print bootargs
bootargs=mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw rootwait
U-Boot >boot
...
...
...

---O---.
|       |                  .-.           o o
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution mityomapl138 ttyS1

Angstrom v2012.05 - Kernel 3.2.0

mityomapl138 login: Started udev Coldplug all Devices                                      [  OK  ]
Started Restore Sound Card State                                       [  OK  ]
Starting Networking...
Started Avahi mDNS/DNS-SD Stack                                        [  OK  ]
Started Login Service                                                  [  OK  ]
davinci_mdio davinci_mdio.0: resetting idled controller
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201)
ADDRCONF(NETDEV_UP): eth0: link is not ready
PHY: 0:03 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Started Networking                                                     [  OK  ]
Starting Getty on tty1...
Started Getty on tty1                                                  [  OK  ]
root
Last login: Sat Jan  1 00:14:13 UTC 2000 on ttyS1
root@mityomapl138:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:C2:BF:8D:B3
          inet6 addr: fe80::250:c2ff:febf:8db3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:276 (276.0 B)  TX bytes:1112 (1.0 KiB)
          Interrupt:33

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@mityomapl138:~#