U-Boot SPL 2013.10-g0451b05 (Jun 16 2017 - 11:39:04) MitySOM335x profile 1 - Model No: 3352-HX-X4A-RC Serial No: 15013530 Critical Link: Error u-boot not compiled with for 1GB nand support. Nand may not function correctly. Configuring for 1024 MB DDR3 @ 400MHz Critical Link AM335X Dev Kit -- NAND Page size = 2048k booting from dev 8 reading u-boot.img reading u-boot.img U-Boot 2013.10-g0451b05 (Jun 16 2017 - 11:39:04) AM335X-GP rev 2 I2C: ready DRAM: 1 GiB WARNING: Caches not enabled Critical Link: Error u-boot not compiled with for 1GB nand support. Nand may not function correctly. NAND: Using 2k bch8 layout ECC Mode = 2 lo = 56/0 1024 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - bad CRC, using default environment Net: cpsw:1 is connected to cpsw. Reconnecting to cpsw cpsw, usb_ether Hit any key to stop autoboot: 0 U-Boot# print bootargs ## Error: "bootargs" not defined U-Boot# run mmc_args U-Boot# print bootargs bootargs=console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none U-Boot# setenv fdtaddr 0x88000000; setenv fdt_high 0xFFFFFFFF; setenv kloadaddr 0x80007fc0 U-Boot# setenv serverip 10.0.102.252 U-Boot# dhcp; tftp $fdtaddr am335x-mitysom.dtb; tftp $kloadaddr zImage; bootz $kloadaddr - $fdtaddr link up on port 0, speed 1000, full duplex link up on port 1, speed 1000, full duplex BOOTP broadcast 1 DHCP client bound to address 10.0.102.156 Using cpsw device TFTP from server 10.0.102.252; our IP address is 10.0.102.156 Filename 'uImage'. Load address: 0x82000000 Loading: ################################################################# ################################################################# ################################################################# ######################################## 1.4 MiB/s done Bytes transferred = 3447288 (3499f8 hex) link up on port 0, speed 1000, full duplex link up on port 1, speed 1000, full duplex Using cpsw device TFTP from server 10.0.102.252; our IP address is 10.0.102.156 Filename 'am335x-mitysom.dtb'. Load address: 0x88000000 Loading: ### 1.4 MiB/s done Bytes transferred = 37210 (915a hex) link up on port 0, speed 1000, full duplex link up on port 1, speed 1000, full duplex Using cpsw device TFTP from server 10.0.102.252; our IP address is 10.0.102.156 Filename 'zImage'. Load address: 0x80007fc0 Loading: ################################################################# ################################################################# ################################################################# ################################################ 1.4 MiB/s done Bytes transferred = 3560808 (365568 hex) Kernel image @ 0x80007fc0 [ 0x000000 - 0x365568 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800c159 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.6-ga7e397a (jhaller@jhaller-VirtualBox) (gcc version 4.8.3 20140401 (prerelease) (Linaro GCC 4.8-2014.04) ) #1 Mon Jun 19 11:50:02 EDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Critical Link MitySOM-335x [ 0.000000] cma: Reserved 24 MiB at 0xbe000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259922 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 993680K/1046528K available (6567K kernel code, 533K rwdata, 2312K rodata, 328K init, 8201K bss, 28272K reserved, 24576K cma-reserved, 243712K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08b3f7c (8880 kB) [ 0.000000] .init : 0xc08b4000 - 0xc0906000 ( 328 kB) [ 0.000000] .data : 0xc0906000 - 0xc098b558 ( 534 kB) [ 0.000000] .bss : 0xc098e000 - 0xc11906f0 (8202 kB) [ 0.000000] Running RCU self tests [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000044] clocksource timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000088] OMAP clocksource: timer1 at 24000000 Hz [ 0.000793] Console: colour dummy device 80x30 [ 0.000844] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000854] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000863] ... MAX_LOCK_DEPTH: 48 [ 0.000872] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000879] ... CLASSHASH_SIZE: 4096 [ 0.000887] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.000895] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.000904] ... CHAINHASH_SIZE: 32768 [ 0.000912] memory used by lock dependency info: 5167 kB [ 0.000921] per task-struct memory footprint: 1152 bytes [ 0.000955] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.088396] pid_max: default: 32768 minimum: 301 [ 0.088651] Security Framework initialized [ 0.088786] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.088805] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.091134] Initializing cgroup subsys blkio [ 0.091182] Initializing cgroup subsys memory [ 0.091278] Initializing cgroup subsys devices [ 0.091347] Initializing cgroup subsys freezer [ 0.091443] Initializing cgroup subsys perf_event [ 0.091511] CPU: Testing write buffer coherency: ok [ 0.092709] Setting up static identity map for 0x80008200 - 0x80008270 [ 0.097563] devtmpfs: initialized [ 0.136666] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.189337] omap_hwmod: tptc0 using broken dt data from edma [ 0.189923] omap_hwmod: tptc1 using broken dt data from edma [ 0.190510] omap_hwmod: tptc2 using broken dt data from edma [ 0.200700] omap_hwmod: debugss: _wait_target_disable failed [ 0.230716] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.233807] pinctrl core: initialized pinctrl subsystem [ 0.238944] NET: Registered protocol family 16 [ 0.244278] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.246413] cpuidle: using governor ladder [ 0.246445] cpuidle: using governor menu [ 0.257307] OMAP GPIO hardware version 0.1 [ 0.283581] omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_default, deferring probe [ 0.288822] No ATAGs? [ 0.288854] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.291939] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.291965] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.336640] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.343973] SCSI subsystem initialized [ 0.345612] usbcore: registered new interface driver usbfs [ 0.345791] usbcore: registered new interface driver hub [ 0.345958] usbcore: registered new device driver usb [ 0.346942] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.347056] omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c1_pins, deferring probe [ 0.347143] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 0.347462] pps_core: LinuxPPS API ver. 1 registered [ 0.347475] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.347535] PTP clock support registered [ 0.349826] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.352775] Switched to clocksource timer1 [ 0.386304] NET: Registered protocol family 2 [ 0.388128] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.388434] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.392051] TCP: Hash tables configured (established 8192 bind 8192) [ 0.392288] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.392916] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.394282] NET: Registered protocol family 1 [ 0.395919] RPC: Registered named UNIX socket transport module. [ 0.395944] RPC: Registered udp transport module. [ 0.395955] RPC: Registered tcp transport module. [ 0.395966] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.398074] CPU PMU: Failed to parse /pmu/interrupt-affinity[0] [ 0.398213] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.402945] futex hash table entries: 256 (order: 1, 11264 bytes) [ 0.403224] audit: initializing netlink subsys (disabled) [ 0.403489] audit: type=2000 audit(0.400:1): initialized [ 0.408084] VFS: Disk quotas dquot_6.6.0 [ 0.408210] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.410370] NFS: Registering the id_resolver key type [ 0.410715] Key type id_resolver registered [ 0.410730] Key type id_legacy registered [ 0.410922] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.418828] NET: Registered protocol family 38 [ 0.419201] bounce: pool size: 64 pages [ 0.419294] io scheduler noop registered [ 0.419318] io scheduler deadline registered [ 0.419365] io scheduler cfq registered (default) [ 0.421947] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.424996] backlight supply power not found, using dummy regulator [ 0.429394] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.435786] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.436401] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 155, base_baud = 3000000) is a OMAP UART0 [ 1.193508] console [ttyO0] enabled [ 1.199323] omap_uart 481a6000.serial: no wakeirq for uart3 [ 1.205651] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 156, base_baud = 3000000) is a OMAP UART3 [ 1.216841] omap_uart 481a8000.serial: no wakeirq for uart4 [ 1.223156] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 157, base_baud = 3000000) is a OMAP UART4 [ 1.236536] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.244130] [drm] Initialized drm 1.1.0 20060810 [ 1.250004] panel panel: pins are not configured [ 1.260996] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.268008] [drm] No driver support for vblank timestamp query. [ 1.328617] Console: switching to colour frame buffer device 100x30 [ 1.340513] tilcdc 4830e000.lcdc: fb0: frame buffer device [ 1.346377] tilcdc 4830e000.lcdc: registered panic notifier [ 1.352310] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 1.387321] brd: module loaded [ 1.407333] loop: module loaded [ 1.414168] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.432597] usbcore: registered new interface driver asix [ 1.438539] usbcore: registered new interface driver ax88179_178a [ 1.445073] usbcore: registered new interface driver cdc_ether [ 1.451344] usbcore: registered new interface driver smsc95xx [ 1.457513] usbcore: registered new interface driver net1080 [ 1.463595] usbcore: registered new interface driver cdc_subset [ 1.469909] usbcore: registered new interface driver zaurus [ 1.476008] usbcore: registered new interface driver cdc_ncm [ 1.482573] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.489457] ehci-omap: OMAP-EHCI Host Controller driver [ 1.495386] usbcore: registered new interface driver cdc_wdm [ 1.501543] usbcore: registered new interface driver usb-storage [ 1.509884] mousedev: PS/2 mouse device common for all mice [ 1.518331] i2c /dev entries driver [ 1.525562] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.535435] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.540337] omap_hsmmc 48060000.mmc: Got WP GPIO [ 1.584281] ledtrig-cpu: registered to indicate activity on CPUs [ 1.591252] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.606144] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.619688] usbcore: registered new interface driver usbhid [ 1.625590] usbhid: USB HID core driver [ 1.630653] remoteproc0: wkup_m3 is available [ 1.635387] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 1.644764] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 1.656953] oprofile: using arm/armv7 [ 1.661670] Initializing XFRM netlink socket [ 1.666418] NET: Registered protocol family 17 [ 1.671152] NET: Registered protocol family 15 [ 1.676289] Key type dns_resolver registered [ 1.681399] omap_voltage_late_init: Voltage driver support not added [ 1.688125] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.696606] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.706614] ThumbEE CPU extension supported. [ 1.711109] SmartReflex Class3 initialized [ 1.716792] remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 [ 1.725861] remoteproc0: failed to load am335x-pm-firmware.elf [ 1.740046] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 1.745703] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 1.753453] omap-gpmc 50000000.gpmc: cannot request GPMC CS 0 [ 1.759476] omap-gpmc 50000000.gpmc: failed to probe DT children [ 1.767763] omap-gpmc: probe of 50000000.gpmc failed with error -16 [ 1.779099] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.786962] mmc0: new high speed SDHC card at address 1234 [ 1.796312] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 400 kHz [ 1.803543] mmcblk0: mmc0:1234 SA04G 3.67 GiB [ 1.815226] mmcblk0: p1 p2 p3 [ 1.824121] tps65910 2-002d: No interrupt support, no core IRQ [ 1.873765] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz [ 1.880260] backlight supply power not found, using dummy regulator [ 1.952863] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 1.959251] davinci_mdio 4a101000.mdio: detected phy mask fffffffd [ 1.969490] libphy: 4a101000.mdio: probed [ 1.973776] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver unknown [ 1.983784] cpsw 4a100000.ethernet: Detected MACID = ec:24:b8:5d:ee:a5 [ 1.994361] hctosys: unable to open rtc device (rtc0) [ 1.999658] sr_init: No PMIC hook to init smartreflex [ 2.005287] sr_init: platform driver register failed for SR [ 2.034233] vbat: disabling [ 2.038507] backlight supply power not found, using dummy regulator [ 2.060187] kjournald starting. Commit interval 5 seconds [ 2.069459] EXT3-fs (mmcblk0p2): using internal journal [ 2.074995] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.082330] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.093434] devtmpfs: mounted [ 2.097178] Freeing unused kernel memory: 328K (c08b4000 - c0906000) INIT: version 2.88 booting Starting udev [ 3.192258] udevd[91]: starting version 182 [ 9.722766] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 9.743184] kjournald starting. Commit interval 5 seconds [ 10.549871] EXT3-fs (mmcblk0p3): using internal journal [ 10.555466] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory bootlogd. [ 11.336080] random: dd urandom read with 73 bits of entropy available Populating dev cache hwclock: can't open '/dev/misc/rtc': No such file or directory Mon Mar 6 19:08:00 UTC 2017 hwclock: can't open '/dev/misc/rtc': No such file or directory INIT: Entering runlevel: 5 Configuring network interfaces... ifup: duplicate interface "usb0" Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 done. creating NFS state directory: done starting statd: done Starting HOSTAP Daemon: Configuration file: /etc/hostapd.conf nl80211: 'nl80211' generic netlink not found Failed to initialize driver 'nl80211' rmdir[ctrl_interface]: No such file or directory /etc/rc5.d/S20hostapd: line 11: 573 Segmentation fault start-stop-daemon -S -x $DAEMON -- $ARGS hwclock: can't open '/dev/misc/rtc': No such file or directory NFS daemon support not enabled in kernel Starting ntpd: done Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] ioctl FBIOPUT_VSCREENINFO: Invalid argument No SGX hardware, not starting PVR Stopping Bootlog daemon: bootlogd. ,--. ,--.,--. ,--. ,---. ,-----. ,--. ,--. | `.' |`--',-' '-.,--. ,--.' .-' ' .-. '| `.' | | |'.'| |,--.'-. .-' \ ' / `. `-. | | | || |'.'| | | | | || | | | \ ' .-' |' '-' '| | | | `--' `--'`--' `--' .-' / `-----' `-----' `--' `--' `---' ,----. ,----. ,-----.,--. ,--. '.-. |'.-. || .--' \ `.' / .' < .' < '--. `\ .' \ /'-' |/'-' |.--' / / .'. \ `----' `----' `----' '--' '--' Critical Link LLC http://support.criticallink.com mitysom-335x /dev/ttyO0 Linux kernel verison Linux armv7l #1 Mon Jun 19 11:50:02 EDT 2017 Critical Link Linux (sysvinit) 1.6.0 mitysom-335x /dev/ttyO0 mitysom-335x login: root root@mitysom-335x:~#