OMAP-L138/AM-1808/AM-1810 initialization passed! Configuring 128MB mDDR Booting TI User Boot Loader UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53 UBL Flashtype: SPI Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. U-Boot 2009.11 (Mar 12 2012 - 11:54:56) I2C: ready DRAM: 128 MB NAND: 256 MiB MMC: davinci: 0 In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ASYNC3 Clock : 150000000 Hz Enet config : 2 MMC 0 Enable : 1 Resetting ethernet phy Net: davinci_eth_phy_detect(), ALIVE = 0x0000003e davinci_eth_phy_detect(), ALIVE = 0x0000003e davinci_eth_phy_detect(), ALIVE = 0x0000003e davinci_eth_phy_detect(), ALIVE = 0x0000003e davinci_eth_phy_detect(), ALIVE = 0x0000003e Hit any key to stop autoboot: 0 8192 KiB M25P64 at 0:0 is now current device ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-3.4.0+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2611872 Bytes = 2.5 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0 Linux version 3.4.0+ (charles@debian) (gcc version 4.5.4 20111126 (prerelease) (GCC) ) #7 PREEMPT Mon May 28 15:03:32 BST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138/MityARM-1808 Ignoring unrecognised tag 0x42000101 Memory policy: ECC disabled, Data cache writethrough BUG: mapping for 0xffff0000 at 0xfffe0000 out of vmalloc space DaVinci da850/omap-l138/am18x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 root=/dev/mmcblk0p1 rw,rootwait ip=192.168.1.100 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 91416k/91416k available, 6888k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc6800000 - 0xff000000 ( 904 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc05265ec (5242 kB) .init : 0xc0527000 - 0xc054e000 ( 156 kB) .data : 0xc054e000 - 0xc05a91a0 ( 365 kB) .bss : 0xc05a91c4 - 0xc05d5774 ( 178 kB) NR_IRQS:245 sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc03356b8 - 0xc0335710 devtmpfs: initialized gpiochip_add: registered GPIOs 0 to 31 on device: DaVinci gpiochip_add: registered GPIOs 32 to 63 on device: DaVinci gpiochip_add: registered GPIOs 64 to 95 on device: DaVinci gpiochip_add: registered GPIOs 96 to 127 on device: DaVinci gpiochip_add: registered GPIOs 128 to 143 on device: DaVinci DaVinci: 144 gpio irqs dummy: NET: Registered protocol family 16 baseboard_pre_init: Entered mityomapl138_setup_nand: using 16 bit data baseboard_init [IndustrialIO]... bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb VDCDC1: 1150 <--> 1350 mV at 1200 mV VDCDC2: 1800 mV VDCDC3: 1200 mV LDO1: 1800 mV LDO2: 2500 <--> 3300 mV at 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.25. Switching to clocksource timer0_1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 178 io scheduler noop registered (default) start plist test end plist test Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write MityOMAPL138: Found MAC = 00:50:c2:bf:8c:4e MityOMAPL138: Part Number = L138-FX-225-RC NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bit) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000007a60000 Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000010000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 spi_davinci spi_davinci.1: master is unqueued, this is deprecated m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" No LCD configured MII PHY configured 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: Controller at 0xfef0e000 Micrel KS8995 Ethernet switch SPI driver version 0.1.1 CAN device driver interface mcp251x spi1.1: MCP251x didn't enter in conf mode after reset mcp251x spi1.1: Probe failed mcp251x spi1.1: probe failed davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask ffffffc1 davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[1]: device davinci_mdio-0:01, driver unknown davinci_mdio davinci_mdio.0: phy[2]: device davinci_mdio-0:02, driver unknown davinci_mdio davinci_mdio.0: phy[3]: device davinci_mdio-0:03, driver unknown davinci_mdio davinci_mdio.0: phy[4]: device davinci_mdio-0:04, driver unknown davinci_mdio davinci_mdio.0: phy[5]: device davinci_mdio-0:05, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) mousedev: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected omap_rtc: already running i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver soc-audio soc-audio.0: ASoC machine MityDSP-L138 INDIO should use snd_soc_register_card() dsd1791 spi1.2: Failed to add route LLOUT->Line Out asoc: dsd1791 <-> davinci-mcasp.0 mapping ok TCP: cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) LDO2: incomplete constraints, leaving on LDO1: incomplete constraints, leaving on mmc0: new high speed SDHC card at address 1234 VDCDC3: incomplete constraints, leaving on mmcblk0: mmc0:1234 SA04G 3.67 GiB VDCDC2: incomplete constraints, leaving on VDCDC1: incomplete constraints, leaving on mmcblk0: p1 console [netcon0] enabled netconsole: network logging started omap_rtc omap_rtc: setting system clock to 2000-01-01 00:02:00 UTC (946684920) davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=davinci_mdio-0:01, id=221450) PHY: davinci_mdio-0:01 - Link is Up - 10/Half IP-Config: Guessing netmask 255.255.255.0 IP-Config: Complete: device=eth0, addr=192.168.1.100, mask=255.255.255.0, gw=255.255.255.255 host=192.168.1.100, domain=, nis-domain=(none) bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= ALSA device list: #0: MityDSP-L138 INDIO PHY: davinci_mdio-0:01 - Link is Up - 100/Full EXT3-fs (mmcblk0p1): warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p1): using internal journal EXT3-fs (mmcblk0p1): recovery complete EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:1. devtmpfs: mounted Freeing init memory: 156K Welcome to The Ångström Distribution! Starting Runtime Directory... Starting Media Directory... Starting Lock Directory... Starting Remount API VFS... Starting udev Coldplug all Devices... Starting udev Kernel Device Manager... Starting File System Check on Root Device... Starting Debug File System... Starting POSIX Message Queue File System... Started Huge Pages File System udevd[1101]: starting version 181 [ OK ] Starting Apply Kernel Variables... Started Set Up Additional Binary Formats [ OK ] Started Security File System [ OK ] Started Load Kernel Modules [ OK ] Started Configuration File System [ OK ] Started FUSE Control File System [ OK ] Starting Journal Service... Started Journal Service [ OK ] Starting LSB: The RPC portmapper... Started udev Kernel Device Manager [ OK ] Started Runtime Directory [ OK ] Started Media Directory [ OK ] Started Lock Directory [ OK ] Started Remount API VFS [ OK ] Started File System Check on Root Device [ OK ] Started Debug File System [ OK ] Started POSIX Message Queue File System [ OK ] Started Apply Kernel Variables [ OK ] Starting Remount Root FS... Started LSB: The RPC portmapper [ OK ] portmap[1131]: Starting portmap daemon... Started Remount Root FS [ OK ] Started Machine ID first boot configure [ OK ] Starting /tmp... Started Opkg first boot configure [ OK ] Started /tmp [ OK ] Starting Recreate Volatile Files and Directories... Starting Load Random Seed... Started Load Random Seed [ OK ] Started Recreate Volatile Files and Directories [ OK ] Starting LSB: Kernel NFS server support... Starting Avahi mDNS/DNS-SD Stack... Started SSH Key Generation [ OK ] Starting D-Bus System Message Bus... Starting Permit User Sessions... Starting Login Service... nfsserver[1336]: creating NFS state directory: done Starting Timestamping service... Started Timestamping service [ OK ] Started Permit User Sessions [ OK ] Started D-Bus System Message Bus [ OK ] nfsserver[1336]: starting 8 nfsd kernel threads: rpc.nfsd: Unable to access /proc/fs/nfsd errno 2 (No such file or directory). nfsserver[1336]: Please try, as root, 'mount -t nfsd nfsd /proc/fs/nfsd' and then restart rpc.nfsd to correct the problem nfsserver[1336]: done Starting Serial Getty on ttyS1... Started Serial Getty on ttyS1 [ OK ] Started Login Service .---O---. | | .-. o o | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom v2012.03-core - Kernel 3.4.0+ mityomapl138 login: nfsserver[1336]: starting mountd: done Started udev Coldplug all Devices [ OK ] Starting Getty on tty1... Started Getty on tty1 [ OK ] nfsserver[1336]: starting statd: done Failed to start LSB: Kernel NFS server support [FAILED] See 'systemctl status nfsserver.service' for details. .---O---. | | .-. o o | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom v2012.03-core - Kernel 3.4.0+ mityomapl138 login: root Last login: Sat Jan 1 07:21:15 UTC 2000 on ttyS1 root@mityomapl138:~# ping 192.168.1.101 PING 192.168.1.101 (192.168.1.101): 56 data bytes ^C --- 192.168.1.101 ping statistics --- 47 packets transmitted, 0 packets received, 100% packet loss root@mityomapl138:~# ping 192.168.1.101 PING 192.168.1.101 (192.168.1.101): 56 data bytes ^C --- 192.168.1.101 ping statistics --- 12 packets transmitted, 0 packets received, 100% packet loss root@mityomapl138:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:50:C2:BF:8C:4E inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:140 (140.0 B) Interrupt:33 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:85 errors:0 dropped:0 overruns:0 frame:0 TX packets:85 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8428 (8.2 KiB) TX bytes:8428 (8.2 KiB) root@mityomapl138:~#