root@mityomapl138:~# dmesg Booting Linux on physical CPU 0 Linux version 3.4.0+ (charles@debian) (gcc version 4.5.4 20111126 (prerelease) (GCC) ) #23 PREEMPT Mon Jun 11 13:31:49 BST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138/MityARM-1808 Ignoring unrecognised tag 0x42000101 Memory policy: ECC disabled, Data cache writethrough BUG: mapping for 0xffff0000 at 0xfffe0000 out of vmalloc space DaVinci da850/omap-l138/am18x variant 0x1 On node 0 totalpages: 24576 free_area_init_node: node 0, pgdat c05a8458, node_mem_map c05d6000 DMA zone: 192 pages used for memmap DMA zone: 0 pages reserved DMA zone: 24384 pages, LIFO batch:3 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 root=/dev/mmcblk0p1 rw,rootwait ip=192.168.1.100 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 91416k/91416k available, 6888k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc6800000 - 0xff000000 ( 904 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc05265ec (5242 kB) .init : 0xc0527000 - 0xc054e000 ( 156 kB) .data : 0xc054e000 - 0xc05a91e0 ( 365 kB) .bss : 0xc05a9204 - 0xc05d57b4 ( 178 kB) NR_IRQS:245 sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc03356d8 - 0xc0335730 devtmpfs: initialized gpiochip_add: registered GPIOs 0 to 31 on device: DaVinci gpiochip_add: registered GPIOs 32 to 63 on device: DaVinci gpiochip_add: registered GPIOs 64 to 95 on device: DaVinci gpiochip_add: registered GPIOs 96 to 127 on device: DaVinci gpiochip_add: registered GPIOs 128 to 143 on device: DaVinci DaVinci: 144 gpio irqs dummy: NET: Registered protocol family 16 baseboard_pre_init: Entered mityomapl138_setup_nand: using 16 bit data baseboard_init [Hawker Siddeley Switchgear Demo Board]... baseboard_setup_spi: Entered bio: create slab at 0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb VDCDC1: 1150 <--> 1350 mV at 1200 mV VDCDC2: 1800 mV VDCDC3: 1200 mV LDO1: 1800 mV LDO2: 2500 <--> 3300 mV at 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.25. Switching to clocksource timer0_1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 178 io scheduler noop registered (default) start plist test end plist test Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write MityOMAPL138: Found MAC = 00:50:c2:bf:8c:4e MityOMAPL138: Part Number = L138-FX-225-RC NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bit) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000007a60000 Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000010000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 spi_davinci spi_davinci.1: registered master spi1 spi_davinci spi_davinci.1: master is unqueued, this is deprecated spi spi1.0: setup mode 0, 8 bits/w, 30000000 Hz max --> 0 m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" No LCD configured MII PHY configured 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: registered child spi1.0 spi spi1.1: setup mode 0, 8 bits/w, 10000000 Hz max --> 0 spi_davinci spi_davinci.1: registered child spi1.1 spi spi1.2: setup mode 0, 8 bits/w, 1000000 Hz max --> 0 spi_davinci spi_davinci.1: registered child spi1.2 spi spi1.3: setup mode 0, 8 bits/w, 5000000 Hz max --> 0 spi_davinci spi_davinci.1: registered child spi1.3 spi_davinci spi_davinci.1: Controller at 0xfef0e000 Micrel KS8995 Ethernet switch SPI driver version 0.1.1 Micrel KS8995 Ethernet switch SPI driver KS8995MA Probe Entered spi-ks8995 spi1.3: setup mode 0, 8 bits/w, 5000000 Hz max --> 0 spi-ks8995 spi1.3: unknown family id:ff CAN device driver interface mcp251x spi1.1: setup mode 0, 8 bits/w, 10000000 Hz max --> 0 mcp251x spi1.1: MCP251x didn't enter in conf mode after reset mcp251x spi1.1: Probe failed mcp251x spi1.1: probe failed davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask ffffffc1 davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[1]: device davinci_mdio-0:01, driver unknown davinci_mdio davinci_mdio.0: phy[2]: device davinci_mdio-0:02, driver unknown davinci_mdio davinci_mdio.0: phy[3]: device davinci_mdio-0:03, driver unknown davinci_mdio davinci_mdio.0: phy[4]: device davinci_mdio-0:04, driver unknown davinci_mdio davinci_mdio.0: phy[5]: device davinci_mdio-0:05, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) mousedev: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver soc-audio soc-audio.0: ASoC machine MityDSP-L138 INDIO should use snd_soc_register_card() dsd1791 spi1.2: Failed to add route LLOUT->Line Out asoc: dsd1791 <-> davinci-mcasp.0 mapping ok TCP: cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) LDO2: incomplete constraints, leaving on LDO1: incomplete constraints, leaving on VDCDC3: incomplete constraints, leaving on mmc0: new high speed SDHC card at address 1234 VDCDC2: incomplete constraints, leaving on mmcblk0: mmc0:1234 SA04G 3.67 GiB VDCDC1: incomplete constraints, leaving on console [netcon0] enabled mmcblk0: p1 mmcblk0: p1 size 7743267 extends beyond EOD, truncated netconsole: network logging started omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) net eth0: no phy, defaulting to 100/full IP-Config: Guessing netmask 255.255.255.0 IP-Config: Complete: device=eth0, addr=192.168.1.100, mask=255.255.255.0, gw=255.255.255.255 host=192.168.1.100, domain=, nis-domain=(none) bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= ALSA device list: #0: MityDSP-L138 INDIO EXT3-fs (mmcblk0p1): warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p1): using internal journal EXT3-fs (mmcblk0p1): recovery complete EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:1. devtmpfs: mounted Freeing init memory: 156K >udevd[1113]: starting version 181 root@mityomapl138:~#