U-Boot 2009.11-00006-g66bcd23-dirty (Dec 14 2011 - 11:33:14) I2C: ready DRAM: 128 MB NAND: 512 MiB MMC: davinci: 0 In: serial Out: serial Err: serial Error - Checksum on MityDSP-L138 Config Block Checksum Invalid You must set the config to FLASH to make permanent ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ASYNC3 Clock : 150000000 Hz Enet config : 2 MMC 0 Enable : 0 Resetting ethernet phy Net: Ethernet PHY: GENERIC @ 0x03 [0x8] Hit any key to stop autoboot: 0 U-Boot > pri bootdelay=3 baudrate=115200 bootfile="uImage" flashuboot=tftp 0xc0700000 mityomap/u-boot-ubl.bin; sf probe 0; sf erase 0x10000 0x80000; sf write 0xc0700000 0x10000 ${filesize} flashkernel=tftp 0xc0700000 mityomap/uImage; sf probe 0; sf erase 0x100000 0x280000; sf write 0xc0700000 0x100000 ${filesize} flashubl=tftp 0xc0700000 mityomap/UBL_SPI_MEM.ais; sf probe 0; sf erase 0 0x10000; sf write 0xc0700000 0 0x10000 flashrootfs=tftp 0xc2000000 mityomap/mityomap-base-mityomapl138.jffs2; nand erase 0 0x08000000; nand write.jffs2 0xc2000000 0 ${filesize} autoload=no mtdids=nand0=nand bootargsbase=mem=96M console=ttyS1,115200n8 flashargs=setenv bootargs ${bootargsbase} ${mtdparts} root=/dev/mtdblock0 rw,noatime rootfstype=jffs2 progfpga=nand device nand0; nand read c4000000 00c00000 00200000; nand read c4000000 00c00000 00200000; updatefpga=tftp c0700000 mityomap/upp.bin; nand device nand0; nand erase c00000 200000; nand erase c00000 200000; nand write c0700000 c00000 200000 updatedsp=tftp c0700000 mityomap/binary.bin; nand device nand0; nand erase 200000 a00000; nand erase 200000 a00000; nand write c0700000 200000 a00000 updatedspbootloader=tftp c0700000 mityomap/dspBoot.out; nand erase 100000 100000; nand write c0700000 100000 100000; mirketboot=run progfpga; nand read c0700000 00100000 00100000; nand read c7000000 00200000 00800000; nand read ca000000 20000 10000; nand read c2500000 30000 10000; loadfpga c4000000 200000; bootdsp 0xc0700000; bootargsbackup=mem=64M console=ttyS2,115200n8 ip=10.2.10.184 nfsroot=10.2.10.183: xport/rfs root=/dev/nfs rw mtdparts=mtdparts=nand:14M(userfs),128M(rootfs),-(unused) partition=nand0,0 mtddevnum=0 mtddevname=userfs bootargs=mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw noatime rootfstype=jffs2 ip=192.168.1.11 filesize=269BB8 fileaddr=C0700000 ipaddr=192.168.1.11 serverip=192.168.1.10 defaultbootcmd=sf probe 0; sf read 0xc0700000 0x100000 0x300000; bootm 0xc0700000 bootcmd=sf probe 0; sf read 0xc0700000 0x100000 0x300000; bootm 0xc0700000 stdin=serial stdout=serial stderr=serial ethaddr=70:b3:d5:b5:1d:93 ver=U-Boot 2009.11-00006-g66bcd23-dirty (Dec 14 2011 - 11:33:14) Environment size: 2148/65532 bytes U-Boot > boot 8192 KiB M25P64 at 0:0 is now current device ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2530168 Bytes = 2.4 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 3.2.0 (root@mitydsp) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #1 PREEMPT Mon Jan 13 11:06:16 EST 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138/MityARM-1808 Ignoring unrecognised tag 0x42000101 Memory policy: ECC disabled, Data cache writethrough DaVinci da850/omap-l138/am18x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw noatime rootfstype=jffs2 ip=192.168.1.11 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 91368k/91368k available, 6936k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc052c598 (5266 kB) .init : 0xc052d000 - 0xc0555000 ( 160 kB) .data : 0xc0556000 - 0xc05b5a80 ( 383 kB) .bss : 0xc05b5aa4 - 0xc05e2490 ( 179 kB) NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized DaVinci: 144 gpio irqs print_constraints: dummy: NET: Registered protocol family 16 baseboard_pre_init: Entered mityomapl138_setup_nand: using 8 bit data baseboard_init [IndustrialIO]... bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV print_constraints: VDCDC2: 1800 mV print_constraints: VDCDC3: 1200 mV print_constraints: LDO1: 1800 mV print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.24. Switching to clocksource timer0_1 musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) Waiting for USB PHY clock good... musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 178 io scheduler noop registered (default) start plist test end plist test Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write MityOMAPL138: Found MAC = 70:b3:d5:b5:1d:93 MityOMAPL138: Part Number = L138-FI-236-RL ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000020000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" Using LCD panel: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ baseboard_setup_lcd: unknown LCD type : ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ MII PHY configured 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: Controller at 0xfef0e000 CAN device driver interface mcp251x spi1.1: probed davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffff7 davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 ata1: SATA link down (SStatus 0 SControl 300) hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected omap_rtc: already running i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver dsd1791 spi1.2: Failed to add route LLOUT->Line Out asoc: dsd1791 <-> davinci-mcasp.0 mapping ok ALSA device list: #0: MityDSP-L138 INDIO TCP cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) regulator_init_complete: LDO2: incomplete constraints, leaving on regulator_init_complete: LDO1: incomplete constraints, leaving on regulator_init_complete: VDCDC3: incomplete constraints, leaving on regulator_init_complete: VDCDC2: incomplete constraints, leaving on regulator_init_complete: VDCDC1: incomplete constraints, leaving on console [netcon0] enabled netconsole: network logging started omap_rtc omap_rtc: setting system clock to 2000-01-01 00:55:04 UTC (946688104) davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201) PHY: 0:03 - Link is Up - 100/Full IP-Config: Guessing netmask 255.255.255.0 IP-Config: Complete: device=eth0, addr=192.168.1.11, mask=255.255.255.0, gw=255.255.255.255, host=192.168.1.11, domain=, nis-domain=(none), bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9d4: 0x48b1 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9d8: 0xb238 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9dc: 0xe34e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e0: 0xe80d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e4: 0xc3f5 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e8: 0xc02c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9ec: 0x01e9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f0: 0x64e4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f4: 0x1012 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f8: 0x01e2 instead Further such events for this erase block will not be printed VFS: Mounted root (jffs2 filesystem) on device 31:0. devtmpfs: mounted Freeing init memory: 160K Failed to mount /sys/kernel/security: No such file or directory Welcome to The Ångström Distribution! NET: Registered protocol family 10 Starting Remount API VFS... Starting Temporary Directory... Starting Load Kernel Modules... Started Set Up Additional Binary Formats [ OK ] Starting Apply Kernel Variables... Starting Debug File System... Started Huge Pages File System [ OK ] Starting POSIX Message Queue File System... Starting File System Check on Root Device... Starting udev Coldplug all Devices... Starting udev Kernel Device Manager... Starting Journal Service... Started Journal Service [ OK ] Starting LSB: The RPC portmapper... Started Remount API VFS [ OK ] Started Temporary Directory [ OK ] Started Load Kernel Modules [ OK ] Started Apply Kernel Variables [ OK ] Started Debug File System [ OK ] Started POSIX Message Queue File System [ OK ] Started File System Check on Root Device [ OK ] Starting Remount Root FS... Started Configuration File System [ OK ] Started FUSE Control File System [ OK ] udevd[1086]: starting version 182 Started udev Kernel Device Manager [ OK ] Started Remount Root FS [ OK ] Started Run pending postinsts [ OK ] Started Machine ID first boot configure [ OK ] Starting Recreate Volatile Files and Directories... Starting Load Random Seed... Started Load Random Seed [ OK ] Started Recreate Volatile Files and Directories [ OK ] Started LSB: The RPC portmapper [ OK ] portmap[1095]: Starting portmap daemon... Starting Avahi mDNS/DNS-SD Stack... Started SSH Key Generation [ OK ] Starting D-Bus System Message Bus... Starting Permit User Sessions... Starting Login Service... Starting Timestamping service... Started Timestamping service [ OK ] Started Permit User Sessions [ OK ] Started D-Bus System Message Bus [ OK ] Starting Serial Getty on ttyS1... Started Serial Getty on ttyS1 [ OK ] .---O---. | | .-. o o | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom v2012.05 - Kernel 3.2.0 mityomapl138 login: Started udev Coldplug all Devices [ OK ] Starting Networking... Started Avahi mDNS/DNS-SD Stack [ OK ] Started Login Service [ OK ] Started Networking [ OK ] Starting Getty on tty1... Started Getty on tty1 [ OK ] root Last login: Sat Jan 1 00:54:23 UTC 2000 on ttyS1 root@mityomapl138:~# shutdown now Stopping Avahi mDNS/DNS-SD Stack... Stopping D-Bus System Message Bus... Stopping Serial Getty on tStopping Getty on tty1... Stopping Login Service... Stopping Timestamping service... Starting Save Random Seed... Stopped Avahi mDNS/DNS-SD Stack [ OK ] Stopped Login Service [ OK ] Stopped D-Bus System Message Bus [ OK ] Stopped Serial Getty on ttyS1 [ OK ] Stopped Getty on tty1 [ OK ] Started Save Random Seed [ OK ] Stopping Permit User Sessions... Stopped Timestamping service [ OK ] Stopped Permit User Sessions [ OK ] Stopping Load Kernel Modules... Stopped Load Kernel Modules [ OK ] Stopping Apply Kernel Variables... Stopped Apply Kernel Variables [ OK ] Starting Notify Audit System and Update UTMP about System Shutdown... Stopping Remount API VFS... Stopped Remount API VFS [ OK ] Stopping Temporary Directory... Stopping Remount Root FS... Stopped Remount Root FS [ OK ] Sending SIGTERM to remaining processes... Sending SIGKILL to remaining processes... Unmounting file systems. Unmounted /sys/kernel/debug. Unmounted /dev/mqueue. Disabling swaps. Detaching loop devices. Detaching DM devices. USB 1.1 clocked from USB 2.0 PHY -- can't power it down System halted.