U-Boot SPL 2013.10-g6c6a700 (Nov 20 2013 - 17:01:23) MityARM335x profile 1 - Model No: 3354-GX-X38-RC Serial No: 133869 Configuring for 512 MB DDR3 @ 303MHz Critical Link AM335X Dev Kit -- NAND Page size = 4096k booting from dev 5 Using 4k bch16 layout ECC Mode = 2 lo = 208/0 nand_spl_load_image: loading 4096 bytes from 100000 to 80800000 nand_spl_load_image: loading 457164 bytes from 100000 to 807fffc0 U-Boot 2013.10-g6c6a700 (Nov 20 2013 - 17:01:23) AM335X-GP rev 0 I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: Using 4k bch16 layout ECC Mode = 2 lo = 208/0 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: cpsw:1 is connected to cpsw. Reconnecting to cpsw cpsw Hit any key to stop autoboot: 0 U-Boot# pri arch=arm baudrate=115200 board=mityarm335x board_name=mityarm335x bootargs=console=ttyO0,115200n8 video=da8xx:bpp=16 noinitrd root=/dev/nfs rootwait nfsroot=192.17.52.249:/home/mitydsp/nfs/targetNFS/,nolock rw ip=dhcp bootcmd=run config_dvi; run nand_boot bootdelay=3 bootfile=uImage config_dvi=i2c dev 1;i2c mw 38 8 3d; i2c mw 38 33 0 cpu=armv7 ethact=cpsw ethaddr=78:c5:e5:bc:50:3f ipaddr=192.17.52.100 kloadaddr=0x80007fc0 loadaddr=0x82000000 nand_boot=echo Booting from nand ...; nandecc hw 2; nand read.i ${kloadaddr} ${nand_src_addr} ${nand_img_siz}; bootm ${kloadaddr} nand_img_siz=0x500000 nand_src_addr=0x340000 nfsopts=nolock rootpath=/home/mitydsp/nfs/targetNFS/ serverip=192.17.52.249 soc=am33xx stderr=serial stdin=serial stdout=serial vendor=cl ver=U-Boot 2013.10-g6c6a700 (Nov 20 2013 - 17:01:23) Environment size: 867/131068 bytes U-Boot# boot Setting bus to 1 Booting from nand ... nandecc disabled NAND read: device 0 offset 0x340000, size 0x500000 Skipping bad block 0x00780000 5242880 bytes read: OK ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3635848 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0+ (mitydsp@mitydsp-dev) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #119 Thu Jul 25 13:02:37 EDT 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: mityarm335x [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 noinitrd root=/dev/nfs rootwait nfsroot=192.17.52.249:/home/mitydsp/nfs/targetp [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 511308k/511308k available, 12980k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc072d000 (7316 kB) [ 0.000000] .init : 0xc072d000 - 0xc076c000 ( 252 kB) [ 0.000000] .data : 0xc076c000 - 0xc0802300 ( 601 kB) [ 0.000000] .bss : 0xc0802324 - 0xc083efb4 ( 244 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.056488] pid_max: default: 32768 minimum: 301 [ 0.056610] Security Framework initialized [ 0.056732] Mount-cache hash table entries: 512 [ 0.057067] CPU: Testing write buffer coherency: ok [ 0.076324] omap_hwmod: gfx: failed to hardreset [ 0.091918] omap_hwmod: pruss: failed to hardreset [ 0.093200] print_constraints: dummy: [ 0.093536] NET: Registered protocol family 16 [ 0.095672] OMAP GPIO hardware version 0.1 [ 0.098144] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.100524] omap_i2c.3: alias fck already exists [ 0.100799] omap_i2c.2: alias fck already exists [ 0.102081] Registering mcspi 1 [2] [ 0.102111] omap2_mcspi.1: alias fck already exists [ 0.102325] Registering mcspi 2 [2] [ 0.102355] omap2_mcspi.2: alias fck already exists [ 0.102600] edma.0: alias fck already exists [ 0.102630] edma.0: alias fck already exists [ 0.102661] edma.0: alias fck already exists [ 0.105773] baseboard_init [MityARM-335x DevKit]... [ 0.106140] omap_hsmmc.0: alias fck already exists [ 0.106536] omap_hsmmc.2: alias fck already exists [ 0.107360] da8xx_lcdc.0: alias fck already exists [ 0.107879] d_can.0: alias fck already exists [ 0.108123] d_can.1: alias fck already exists [ 0.108367] Configuring audio... [ 0.108428] Registering mcasp[1] [ 0.108459] davinci-mcasp.1: alias fck already exists [ 0.108947] omap_i2c.1: alias fck already exists [ 0.109161] WLAN GPIO Info.. IRQ = 186 WL_EN = 100 BT_EN = -22 [ 0.109161] Bluetooth not Enabled! [ 0.109222] baseboard_setup_wlan: finished [ 0.132843] bio: create slab at 0 [ 0.134979] SCSI subsystem initialized [ 0.137145] usbcore: registered new interface driver usbfs [ 0.137481] usbcore: registered new interface driver hub [ 0.137664] usbcore: registered new device driver usb [ 0.137817] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3 [ 0.138122] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0 [ 0.139221] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.140136] tps65910 3-002d: JTAGREVNUM 0x1 [ 0.142456] print_constraints: VRTC: [ 0.143859] print_constraints: VIO: at 1500 mV [ 0.146087] print_constraints: VDD1: 600 <--> 1500 mV at 1137 mV normal [ 0.148284] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.149261] print_constraints: VDD3: 5000 mV [ 0.150634] print_constraints: VDIG1: at 1800 mV [ 0.152008] print_constraints: VDIG2: at 1800 mV [ 0.153411] print_constraints: VPLL: at 1800 mV [ 0.154785] print_constraints: VDAC: at 1800 mV [ 0.156188] print_constraints: VAUX1: at 1800 mV [ 0.157562] print_constraints: VAUX2: at 3300 mV [ 0.158966] print_constraints: VAUX33: at 3300 mV [ 0.160339] print_constraints: VMMC: at 3300 mV [ 0.160827] tps65910 3-002d: No interrupt support, no core IRQ [ 0.161010] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 0.161590] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.162719] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.164001] cfg80211: Calling CRDA to update world regulatory domain [ 0.165039] Switching to clocksource gp timer [ 0.180145] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.180328] musb-hdrc musb-hdrc.0: dma type: pio [ 0.181213] musb-hdrc musb-hdrc.0: USB OTG mode controller at e081c000 using PIO, IRQ 18 [ 0.181396] musb-hdrc musb-hdrc.1: dma type: pio [ 0.181762] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.181854] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 0.181976] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.181976] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.181976] usb usb1: Product: MUSB HDRC host driver [ 0.182006] usb usb1: Manufacturer: Linux 3.2.0+ musb-hcd [ 0.182006] usb usb1: SerialNumber: musb-hdrc.1 [ 0.182769] hub 1-0:1.0: USB hub found [ 0.182800] hub 1-0:1.0: 1 port detected [ 0.183319] musb-hdrc musb-hdrc.1: USB OTG mode controller at e081e800 using PIO, IRQ 19 [ 0.183746] NET: Registered protocol family 2 [ 0.183929] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.184204] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.184509] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.184692] TCP: Hash tables configured (established 16384 bind 16384) [ 0.184692] TCP reno registered [ 0.184722] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.184722] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.184906] NET: Registered protocol family 1 [ 0.185241] RPC: Registered named UNIX socket transport module. [ 0.185241] RPC: Registered udp transport module. [ 0.185272] RPC: Registered tcp transport module. [ 0.185272] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.185485] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.185699] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 0.185729] Registering NAND on CS0 [ 0.204681] VFS: Disk quotas dquot_6.5.2 [ 0.204742] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.205291] msgmni has been set to 998 [ 0.206146] io scheduler noop registered [ 0.206146] io scheduler deadline registered [ 0.206207] io scheduler cfq registered (default) [ 0.207183] _regulator_get: tps6116x supply vlcd not found, using dummy regulator [ 0.210052] tps6116x tps6116x: registered backlight controller [ 0.210571] DA8XX FB - options = bpp=16 [ 0.210723] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 800x600 panel [ 0.211700] DA8XX FB: 1024 x 768 16 bpp [ 0.226654] Console: switching to colour frame buffer device 128x48 [ 0.236663] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.238464] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.959472] console [ttyO0] enabled [ 0.963592] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 0.971160] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 0.978637] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.986114] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 0.993530] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 1.010162] brd: module loaded [ 1.018066] loop: module loaded [ 1.021392] i2c-core: driver [tsl2550] using legacy suspend method [ 1.027587] i2c-core: driver [tsl2550] using legacy resume method [ 1.033752] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write [ 1.046081] MityARM-335x: Factory Config Version Wrong (10002) [ 1.054107] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes) [ 1.059478] Creating 1 MTD partitions on "spi_flash": [ 1.064544] 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.072296] omap2-nand driver initializing [ 1.076751] ONFI flash detected [ 1.080017] ONFI param page 0 valid [ 1.083496] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP) [ 1.091552] Creating 8 MTD partitions on "omap2-nand.0": [ 1.096893] 0x000000000000-0x000000040000 : "SPL" [ 1.102905] 0x000000040000-0x000000080000 : "SPL.backup1" [ 1.109588] 0x000000080000-0x0000000c0000 : "SPL.backup2" [ 1.116241] 0x0000000c0000-0x000000100000 : "SPL.backup3" [ 1.122863] 0x000000100000-0x000000300000 : "U-Boot" [ 1.129455] 0x000000300000-0x000000340000 : "U-Boot Env" [ 1.136108] 0x000000340000-0x000000840000 : "Kernel" [ 1.143310] 0x000000840000-0x000020000000 : "File System" [ 1.250396] OneNAND driver initializing [ 1.255676] CAN device driver interface [ 1.259521] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.265747] d_can d_can.0: device registered (irq=52, irq_obj=53) [ 1.272460] d_can d_can.1: device registered (irq=55, irq_obj=56) [ 1.325683] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.331878] davinci_mdio davinci_mdio.0: detected phy mask fffffffd [ 1.338562] am335x_vsc8601_phy_fixup 70421 here addr = 1 [ 1.344543] davinci_mdio.0: probed [ 1.347961] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown [ 1.355468] usbcore: registered new interface driver cdc_ether [ 1.361511] usbcore: registered new interface driver cdc_subset [ 1.367492] Initializing USB Mass Storage driver... [ 1.372619] usbcore: registered new interface driver usb-storage [ 1.378631] USB Mass Storage support registered. [ 1.383331] gadget: using random self ethernet address [ 1.388580] gadget: using random host ethernet address [ 1.394348] usb0: MAC 82:a3:cd:13:87:20 [ 1.398193] usb0: HOST MAC 7e:e9:80:be:e9:6f [ 1.402526] gadget: Ethernet Gadget, version: Memorial Day 2008 [ 1.408569] gadget: g_ether ready [ 1.411987] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 1.417327] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 [ 1.424835] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.431640] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.438873] usb usb2: Product: MUSB HDRC host driver [ 1.443847] usb usb2: Manufacturer: Linux 3.2.0+ musb-hcd [ 1.449249] usb usb2: SerialNumber: musb-hdrc.0 [ 1.454559] hub 2-0:1.0: USB hub found [ 1.458343] hub 2-0:1.0: 1 port detected [ 1.463317] mousedev: PS/2 mouse device common for all mice [ 1.470001] input: ti-tsc-adcc as /devices/platform/tsc/input/input0 [ 1.477447] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 [ 1.484039] i2c /dev entries driver [ 1.488372] Linux media interface: v0.10 [ 1.492462] Linux video capture interface: v2.00 [ 1.497436] usbcore: registered new interface driver uvcvideo [ 1.503173] USB Video Class driver (1.1.1) [ 1.511718] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.519989] cpuidle: using governor ladder [ 1.524566] cpuidle: using governor menu [ 1.534576] usbcore: registered new interface driver usbhid [ 1.540191] usbhid: USB HID core driver [ 1.544616] usbcore: registered new interface driver snd-usb-audio [ 1.566253] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver [ 1.590179] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok [ 1.597473] ALSA device list: [ 1.600463] #0: MityARM-335X DevKit [ 1.604095] oprofile: hardware counters not available [ 1.609191] oprofile: using timer interrupt. [ 1.613494] nf_conntrack version 0.5.0 (7989 buckets, 31956 max) [ 1.620025] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.625457] TCP cubic registered [ 1.628723] NET: Registered protocol family 17 [ 1.633178] can: controller area network core (rev 20090105 abi 8) [ 1.639434] NET: Registered protocol family 29 [ 1.643920] can: raw protocol (rev 20090105) [ 1.648223] can: broadcast manager protocol (rev 20090105 t) [ 1.653900] lib80211: common routines for IEEE802.11 drivers [ 1.659637] Registering the dns_resolver key type [ 1.664398] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.672088] ThumbEE CPU extension supported. [ 1.676422] mux: Failed to setup hwmod io irq -22 [ 1.681762] Power Management for AM33XX family [ 1.686401] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.692779] Copied the M3 firmware to UMEM [ 1.696929] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift [ 1.710601] Detected MACID=78:c5:e5:bc:50:3e [ 1.716461] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.727294] PHY 0:00 not found [ 1.730407] am335x_vsc8601_phy_fixup 70421 here addr = 1 [ 1.736450] [ 1.736480] CPSW phy found : id is : 0x70421 [ 1.774597] mmc0: new high speed SDHC card at address e624 [ 1.780822] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 1.798858] mmcblk0: p1 p2 p3 [ 5.737060] PHY: 0:01 - Link is Up - 1000/Full [ 5.766265] Sending DHCP requests ., OK [ 6.286743] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.17.52.100 [ 6.294830] IP-Config: Complete: [ 6.298095] device=eth0, addr=192.17.52.100, mask=255.255.255.0, gw=192.17.52.1, [ 6.305664] host=192.17.52.100, domain=, nis-domain=(none), [ 6.311676] bootserver=0.0.0.0, rootserver=192.17.52.249, rootpath= [ 6.375793] VFS: Mounted root (nfs filesystem) on device 0:14. [ 6.382019] Freeing init memory: 252K [ 7.302764] udevd (819): /proc/819/oom_adj is deprecated, please use /proc/819/oom_score_adj instead. [ 12.314910] FAT-fs (mmcblk0): bogus number of reserved sectors [ 12.320800] FAT-fs (mmcblk0): Can't find a valid FAT filesystem [ 12.338073] EXT3-fs (mmcblk0): error: can't find ext3 filesystem on dev mmcblk0. [ 12.347717] EXT2-fs (mmcblk0): error: can't find an ext2 filesystem on dev mmcblk0. [ 12.360015] cramfs: wrong magic [ 12.364898] FAT-fs (mmcblk0): bogus number of reserved sectors [ 12.370788] FAT-fs (mmcblk0): Can't find a valid FAT filesystem [ 13.282592] kjournald starting. Commit interval 5 seconds [ 13.288208] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended [ 13.311584] EXT3-fs (mmcblk0p3): using internal journal [ 13.316925] EXT3-fs (mmcblk0p3): recovery complete [ 13.321716] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode [ 13.531768] kjournald starting. Commit interval 5 seconds [ 13.537353] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 13.548889] EXT3-fs (mmcblk0p2): using internal journal [ 13.554138] EXT3-fs (mmcblk0p2): recovery complete [ 13.558959] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 13.645507] alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode. [ 16.727020] pvrsrvkm: disagrees about version of symbol module_layout [ 16.998474] Unhandled fault: external abort on non-linefetch (0x1018) at 0x40312014 ,--. ,--.,--. ,--. ,---. ,------. ,--. ,--. | `.' |`--',-' '-.,--. ,--./ O \ | .--. '| `.' | | |'.'| |,--.'-. .-' \ ' /| .-. || '--'.'| |'.'| | | | | || | | | \ ' | | | || |\ \ | | | `--' `--'`--' `--' .-' / `--' `--'`--' '--'`--' `--' `---' ,----. ,----. ,-----.,--. ,--. '.-. |'.-. || .--' \ `.' / .' < .' < '--. `\ .' \ /'-' |/'-' |.--' / / .'. \ `----' `----' `----' '--' '--' Critical Link LLC http://support.criticallink.com mityarm-335x ttyO0 Linux kernel verison Linux armv7l #119 Thu Jul 25 13:02:37 EDT 2013 mityarm-335x login: root root@mityarm-335x:~#