U-Boot SPL 2013.10-g6c6a700 (Nov 20 2013 - 16:56:02) MityARM335x profile 1 - Model No: 3359-GX-226-RC Serial No: 123765 Old factory config found, configuring for 256 MB DDR2 Configuring for 256 MB DDR2 @ 266MHz Critical Link AM335X Dev Kit -- NAND Page size = 2048k booting from dev 8 reading u-boot.img reading u-boot.img U-Boot 2013.10-g6c6a700 (Nov 20 2013 - 16:56:02) AM335X-GP rev 0 I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: Using 2k bch8 layout ECC Mode = 2 lo = 56/0 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - bad CRC, using default environment Net: cpsw:1 is connected to cpsw. Reconnecting to cpsw cpsw Hit any key to stop autoboot: 1  0 SD/MMC found on device 0 reading uenv.txt 2162 bytes read in 5 ms (421.9 KiB/s) Loaded environment from uenv.txt Importing environment from mmc ... reading uImage 3704240 bytes read in 426 ms (8.3 MiB/s) ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0-00217-g3c4aa5c Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3704176 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-00217-g3c4aa5c (root@dlinux) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 Tue Mar 11 09:16:03 PDT 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: mityarm335x [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 251288k/251288k available, 10856k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0746000 (7416 kB) [ 0.000000] .init : 0xc0746000 - 0xc0784000 ( 248 kB) [ 0.000000] .data : 0xc0784000 - 0xc081d468 ( 614 kB) [ 0.000000] .bss : 0xc081d48c - 0xc085ceb4 ( 255 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000152] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.058959] pid_max: default: 32768 minimum: 301 [ 0.059082] Security Framework initialized [ 0.059173] Mount-cache hash table entries: 512 [ 0.059570] CPU: Testing write buffer coherency: ok [ 0.079620] omap_hwmod: gfx: failed to hardreset [ 0.095886] omap_hwmod: pruss: failed to hardreset [ 0.097259] print_constraints: dummy: [ 0.097625] NET: Registered protocol family 16 [ 0.099914] OMAP GPIO hardware version 0.1 [ 0.102569] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.105102] omap_i2c.3: alias fck already exists [ 0.105407] omap_i2c.2: alias fck already exists [ 0.106109] Registering mcspi 1 [2] [ 0.106170] omap2_mcspi.1: alias fck already exists [ 0.106384] Registering mcspi 2 [2] [ 0.106414] omap2_mcspi.2: alias fck already exists [ 0.106689] edma.0: alias fck already exists [ 0.106719] edma.0: alias fck already exists [ 0.106719] edma.0: alias fck already exists [ 0.110137] baseboard_init [MityARM-335x DevKit]... [ 0.110565] omap_hsmmc.0: alias fck already exists [ 0.110992] omap_hsmmc.2: alias fck already exists [ 0.111907] da8xx_lcdc.0: alias fck already exists [ 0.112426] d_can.0: alias fck already exists [ 0.112701] d_can.1: alias fck already exists [ 0.112945] Configuring audio... [ 0.113037] Registering mcasp[1] [ 0.113067] davinci-mcasp.1: alias fck already exists [ 0.113677] omap_i2c.1: alias fck already exists [ 0.113922] WLAN GPIO Info.. IRQ = 186 WL_EN = 100 BT_EN = -22 [ 0.113922] Bluetooth not Enabled! [ 0.113983] baseboard_setup_wlan: finished [ 0.138763] bio: create slab at 0 [ 0.141052] SCSI subsystem initialized [ 0.143157] usbcore: registered new interface driver usbfs [ 0.143493] usbcore: registered new interface driver hub [ 0.143707] usbcore: registered new device driver usb [ 0.143859] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3 [ 0.144165] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0 [ 0.159027] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.160034] tps65910 3-002d: JTAGREVNUM 0x1 [ 0.162445] print_constraints: VRTC: [ 0.163940] print_constraints: VIO: at 1800 mV [ 0.166259] print_constraints: VDD1: 600 <--> 1500 mV at 1137 mV normal [ 0.168579] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.169586] print_constraints: VDD3: 5000 mV [ 0.171051] print_constraints: VDIG1: at 1800 mV [ 0.172485] print_constraints: VDIG2: at 1800 mV [ 0.173980] print_constraints: VPLL: at 1800 mV [ 0.175415] print_constraints: VDAC: at 1800 mV [ 0.176849] print_constraints: VAUX1: at 1800 mV [ 0.178283] print_constraints: VAUX2: at 3300 mV [ 0.179748] print_constraints: VAUX33: at 3300 mV [ 0.181182] print_constraints: VMMC: at 3300 mV [ 0.181732] tps65910 3-002d: No interrupt support, no core IRQ [ 0.199035] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 0.219024] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.220184] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.221588] cfg80211: Calling CRDA to update world regulatory domain [ 0.222778] Switching to clocksource gp timer [ 0.238952] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.239135] musb-hdrc musb-hdrc.0: dma type: pio [ 0.240081] musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using PIO, IRQ 18 [ 0.240234] musb-hdrc musb-hdrc.1: dma type: pio [ 0.240661] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.240753] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 0.240875] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.240905] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.240905] usb usb1: Product: MUSB HDRC host driver [ 0.240936] usb usb1: Manufacturer: Linux 3.2.0-00217-g3c4aa5c musb-hcd [ 0.240936] usb usb1: SerialNumber: musb-hdrc.1 [ 0.241729] hub 1-0:1.0: USB hub found [ 0.241760] hub 1-0:1.0: 1 port detected [ 0.242340] musb-hdrc musb-hdrc.1: USB OTG mode controller at d081e800 using PIO, IRQ 19 [ 0.242797] NET: Registered protocol family 2 [ 0.243072] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.243377] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.243530] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.243621] TCP: Hash tables configured (established 8192 bind 8192) [ 0.243652] TCP reno registered [ 0.243652] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.243682] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.243896] NET: Registered protocol family 1 [ 0.244171] RPC: Registered named UNIX socket transport module. [ 0.244201] RPC: Registered udp transport module. [ 0.244201] RPC: Registered tcp transport module. [ 0.244201] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.244415] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.256744] VFS: Disk quotas dquot_6.5.2 [ 0.256835] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.257385] msgmni has been set to 490 [ 0.258270] io scheduler noop registered [ 0.258270] io scheduler deadline registered [ 0.258361] io scheduler cfq registered (default) [ 0.259368] _regulator_get: tps6116x supply vlcd not found, using dummy regulator [ 0.262390] tps6116x tps6116x: registered backlight controller [ 0.263031] DA8XX FB - options = bpp=16 [ 0.263183] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 800x600 panel [ 0.264221] DA8XX FB: 1024 x 768 16 bpp [ 0.280120] Console: switching to colour frame buffer device 128x48 [ 0.290466] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.292358] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 1.038391] console [ttyO0] enabled [ 1.042724] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 1.050750] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 1.058624] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 1.066436] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 1.074249] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 1.092041] brd: module loaded [ 1.100433] loop: module loaded [ 1.103973] i2c-core: driver [tsl2550] using legacy suspend method [ 1.110412] i2c-core: driver [tsl2550] using legacy resume method [ 1.116851] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write [ 1.129699] MityARM-335x: Part Number = 3359-GX-226-RC [ 1.135070] MityARM-335x DevKit: factory_config_callback [ 1.141174] Configuring 256MB NAND device [ 1.146179] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.151184] Registering NAND on CS0 [ 1.157836] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes) [ 1.163391] Creating 1 MTD partitions on "spi_flash": [ 1.168731] 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.176940] omap2-nand driver initializing [ 1.181549] ONFI flash detected [ 1.184997] ONFI param page 0 valid [ 1.188629] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP) [ 1.197021] Creating 8 MTD partitions on "omap2-nand.0": [ 1.202575] 0x000000000000-0x000000020000 : "SPL" [ 1.208953] 0x000000020000-0x000000040000 : "SPL.backup1" [ 1.215942] 0x000000040000-0x000000060000 : "SPL.backup2" [ 1.222900] 0x000000060000-0x000000080000 : "SPL.backup3" [ 1.229919] 0x000000080000-0x000000260000 : "U-Boot" [ 1.237304] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.244293] 0x000000280000-0x000000780000 : "Kernel" [ 1.252899] 0x000000780000-0x000010000000 : "File System" [ 1.363006] OneNAND driver initializing [ 1.368041] CAN device driver interface [ 1.372039] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.378540] d_can d_can.0: device registered (irq=52, irq_obj=53) [ 1.385589] d_can d_can.1: device registered (irq=55, irq_obj=56) [ 1.433563] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.440002] davinci_mdio davinci_mdio.0: detected phy mask fffffffd [ 1.447021] am335x_vsc8601_phy_fixup 70421 here addr = 1 [ 1.453277] davinci_mdio.0: probed [ 1.456848] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown [ 1.464660] usbcore: registered new interface driver cdc_ether [ 1.470916] usbcore: registered new interface driver cdc_subset [ 1.477172] Initializing USB Mass Storage driver... [ 1.482513] usbcore: registered new interface driver usb-storage [ 1.488769] USB Mass Storage support registered. [ 1.493682] gadget: using random self ethernet address [ 1.499145] gadget: using random host ethernet address [ 1.505157] usb0: MAC 32:a6:1a:c5:7d:91 [ 1.509185] usb0: HOST MAC 1a:5a:83:9e:c4:9f [ 1.513732] gadget: Ethernet Gadget, version: Memorial Day 2008 [ 1.519989] gadget: g_ether ready [ 1.523590] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 1.529144] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 [ 1.536987] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.544097] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.551605] usb usb2: Product: MUSB HDRC host driver [ 1.556793] usb usb2: Manufacturer: Linux 3.2.0-00217-g3c4aa5c musb-hcd [ 1.563690] usb usb2: SerialNumber: musb-hdrc.0 [ 1.569244] hub 2-0:1.0: USB hub found [ 1.573181] hub 2-0:1.0: 1 port detected [ 1.578491] mousedev: PS/2 mouse device common for all mice [ 1.585601] input: ti-tsc-adcc as /devices/platform/omap/tsc/input/input0 [ 1.594238] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 [ 1.603820] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0 [ 1.617095] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc1 [ 1.625335] i2c /dev entries driver [ 1.630157] Linux media interface: v0.10 [ 1.634826] Linux video capture interface: v2.00 [ 1.640350] usbcore: registered new interface driver uvcvideo [ 1.646667] USB Video Class driver (1.1.1) [ 1.683929] lm75 1-0048: hwmon0: sensor 'lm75' [ 1.690612] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.699859] cpuidle: using governor ladder [ 1.705017] cpuidle: using governor menu [ 1.717041] usbcore: registered new interface driver usbhid [ 1.723205] usbhid: USB HID core driver [ 1.728454] usbcore: registered new interface driver snd-usb-audio [ 1.762054] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver [ 1.782989] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok [ 1.790954] ALSA device list: [ 1.794403] #0: MityARM-335X DevKit [ 1.798553] oprofile: hardware counters not available [ 1.804138] oprofile: using timer interrupt. [ 1.808929] nf_conntrack version 0.5.0 (3926 buckets, 15704 max) [ 1.816040] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.822052] TCP cubic registered [ 1.825744] NET: Registered protocol family 17 [ 1.830718] can: controller area network core (rev 20090105 abi 8) [ 1.837615] NET: Registered protocol family 29 [ 1.842620] can: raw protocol (rev 20090105) [ 1.847412] can: broadcast manager protocol (rev 20090105 t) [ 1.853668] lib80211: common routines for IEEE802.11 drivers [ 1.859924] Registering the dns_resolver key type [ 1.865264] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.873901] ThumbEE CPU extension supported. [ 1.878723] mux: Failed to setup hwmod io irq -22 [ 1.884643] Power Management for AM33XX family [ 1.889831] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.896820] Copied the M3 firmware to UMEM [ 1.901428] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift [ 1.917877] Detected MACID=0:17:ea:9e:70:e9 [ 1.924255] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 1.933837] Waiting for root device /dev/mmcblk0p2... [ 1.951995] mmc0: new high speed SDHC card at address aaaa [ 1.958770] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.965545] mmcblk0: p1 p2 p3 [ 2.259552] kjournald starting. Commit interval 5 seconds [ 2.265716] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 2.277160] EXT3-fs (mmcblk0p2): using internal journal [ 2.282928] EXT3-fs (mmcblk0p2): recovery complete [ 2.289581] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.297149] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.304168] Freeing init memory: 248K INIT: version 2.86 booting Please wait: booting... Starting udev [ 2.880889] udevd (825): /proc/825/oom_adj is deprecated, please use /proc/825/oom_score_adj instead. [ 8.647399] kjournald starting. Commit interval 5 seconds [ 8.653503] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended [ 8.666290] EXT3-fs (mmcblk0p3): using internal journal [ 8.672088] EXT3-fs (mmcblk0p3): recovery complete [ 8.677459] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode [ 8.806823] alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode. Remounting root file system... Caching udev devnodes ALSA: Restoring mixer settings... Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device eth0 No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device eth1 No such device ifconfig: SIOCGIFFLAGS: No such device done. Setting up IP spoofing protection: rp_filter. Sat Dec 24 10:11:00 UTC 2011 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Hardware abstraction layer hald Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Starting PVR [ 14.038879] pvrsrvkm: disagrees about version of symbol module_layout insmod: error inserting '/lib/modules/3.1.0/kernel/drivers/gpu/pvr/pvrsrvkm.ko': -1 Invalid module format FATAL: Module omaplfb not found. FATAL: Module bufferclass_ti not found. BusyBox v1.13.2 (2011-12-15 15:46:39 CST) multi-call binary Usage: mknod [OPTIONS] NAME TYPE MAJOR MINOR Create a special file (block, character, or pipe) Options: -m Create the special file using the specified mode (default a=rw) TYPEs include: b: Make a block device c or u: Make a character device p: Make a named pipe (MAJOR and MINOR are ignored) chmod: /dev/pvrsrvkm: No such file or directory [ 14.166717] Unhandled fault: external abort on non-linefetch (0x1018) at 0x4027c014 Bus error Starting Lighttpd Web Server: lighttpd. 2011-12-24 10:11:02: (log.c.166) server started / / Starting Matrix GUI application. FATAL: Module g_mass_storage not found. *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-dev binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** ,--. ,--.,--. ,--. ,---. ,------. ,--. ,--. | `.' |`--',-' '-.,--. ,--./ O \ | .--. '| `.' | | |'.'| |,--.'-. .-' \ ' /| .-. || '--'.'| |'.'| | | | | || | | | \ ' | | | || |\ \ | | | `--' `--'`--' `--' .-' / `--' `--'`--' '--'`--' `--' `---' ,----. ,----. ,-----.,--. ,--. '.-. |'.-. || .--' \ `.' / .' < .' < '--. `\ .' \ /'-' |/'-' |.--' / / .'. \ `----' `----' `----' '--' '--' Critical Link LLC http://support.criticallink.com mityarm-335x ttyO0 Linux kernel verison Linux armv7l #1 Tue Mar 11 09:16:03 PDT 2014 mityarm-335x login: root root@mityarm-335x:~# ifconfig /a ifconfig: /a: error fetching interface information: Device not found root@mityarm-335x:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:136 errors:0 dropped:0 overruns:0 frame:0 TX packets:136 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:245997 (240.2 KiB) TX bytes:245997 (240.2 KiB) root@mityarm-335x:~#