OMAP-L138/AM-1808/AM-1810 initialization passed! Configuring 256MB mDDR Booting TI User Boot Loader UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53 UBL Flashtype: SPI Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. U-Boot 2009.11 (Jan 13 2014 - 11:14:02) I2C: ready DRAM: 128 MB NAND: 512 MiB MMC: davinci: 0 In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ASYNC3 Clock : 150000000 Hz Enet config : 2 MMC 0 Enable : 0 Resetting ethernet phy Net: Ethernet PHY: GENERIC @ 0x03 [0x8] Hit any key to stop autoboot: 0 8192 KiB M25P64 at 0:0 is now current device ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.34-rc1-00003-g8bdeae6- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2218184 Bytes = 2.1 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.34-rc1-00003-g8bdeae6-dirty (root@mitydsp-dev) (gcc version 4.3.3 (GCC) ) #8 PREEMPT Tue Nov 17 20:01:39 EST 2015 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138 Peripheral Config Block Found Enet_Config = 2 PHYMask = 0x8 LCD Configured : NEC_NL4827HC19-05B UART[0] = 0, 0, 0, 115200 UART[1] = 1, 1, 0, 115200 UART[2] = 0, 0, 0, 115200 SPI[0] = 0, 0, 00, 0, 0 SPI[1] = 1, 1, 01, 0, 30000000 Memory policy: ECC disabled, Data cache writethrough DaVinci da850/omap-l138/am18xx variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mtdblock0 rw,noatime rootfstype=jffs2 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 92616k/92616k available, 5688k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xff000000 - 0xffe00000 ( 14 MB) vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc002b000 ( 140 kB) .text : 0xc002b000 - 0xc0434000 (4132 kB) .data : 0xc0450000 - 0xc0484f80 ( 212 kB) Experimental preemptable hierarchical RCU implementation. NR_IRQS:445 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 NET: Registered protocol family 16 mityomapl138_init... mityomapl138_setup_nand: using 8 bit data EMAC: MII PHY configured, RMII PHY will not be functional mityomapl138_init: setting phy_mask to 8 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb regulator: VDCDC1: 1150 <--> 1350 mV at 1200 mV regulator: VDCDC2: 1710 <--> 1910 mV at 3300 mV regulator: VDCDC3: 1120 <--> 1320 mV at 1800 mV regulator: LDO1: 1800 mV regulator: LDO2: 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.22.1. Switching to clocksource timer0_1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 180 io scheduler noop registered (default) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM (read-only) MityOMAPL138: Found MAC = 70:b3:d5:ef:9e:1b MityOMAPL138: Part Number = L138-FI-236-RL MityOMAPL138: setting max frequency to 456 MHz ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci ata1: SATA max UDMA/133 irq 67 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000020000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 spi_davinci spi_davinci.1: Controller at 0xfef0e000 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected omap_rtc: already running i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver No device for DAI AD73311 Asahi Kasei AK4104 ALSA SoC Codec Driver No device for DAI AK4535 Cirrus Logic CS4270 ALSA SoC Codec Driver No device for codec dsd1791 No device for DAI dsd1791 No device for DAI PCM3008 HiFi No device for DAI SSM2602 No device for DAI tlv320aic23 No device for DAI UDA134X No device for DAI WM8510 HiFi No device for DAI WM8728 No device for DAI WM8750 No device for DAI WM8971 No device for DAI WM8990 ADC/DAC Primary ALSA device list: No soundcards found. TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused i2c1 Clocks: disable unused emac Clocks: disable unused mcasp Clocks: disable unused lcdc Clocks: disable unused mmcsd Clocks: disable unused spi0 Clocks: disable unused mcbsp0 Clocks: disable unused mcbsp1 Clocks: disable unused vpif Clocks: disable unused ecap Clocks: disable unused ehrpwm regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on ata1: SATA link down (SStatus 0 SControl 300) regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on emac-mii: probed omap_rtc omap_rtc: setting system clock to 2013-04-08 18:22:33 UTC (1365445353) Empty flash at 0x045cfe40 ends at 0x045d0000 Empty flash at 0x05d550e4 ends at 0x05d55800 Empty flash at 0x063b29bc ends at 0x063b3000 Empty flash at 0x07bfbc90 ends at 0x07bfc000 VFS: Mounted root (jffs2 filesystem) on device 31:0. Freeing init memory: 140K INIT: version 2.86 booting Please wait: booting... Starting udev JFFS2 notice: (916) check_node_data: wrong data CRC in data node at 0x063b1978: read 0x95369409, calculated 0xe02082db. udev: starting version 151 Remounting root file system... Caching udev devnodes Populating dev cache Configuring network interfaces... eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:03, id=40005201) udhcpc (v1.13.2) started run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1 Sending discover... PHY: 1:03 - Link is Up - 100/Full Sending discover... Sending select for 192.168.0.38... Lease of 192.168.0.38 obtained, lease time 7200 run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1 adding dns 210.220.163.82 adding dns 219.250.36.130 done. Starting portmap daemon: portmap. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. creating NFS state directory: done starting 8 nfsd kernel threads: done starting mountd: done starting statd: done Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom 2010.7-test-20101202 mityomapl138 ttyS1 mityomapl138 login: root root@mityomapl138:~# root@mityomapl138:~# root@mityomapl138:~# cd /app root@mityomapl138:/app# ls -al drwxr-xr-x 2 root root 0 Apr 8 2013 . drwxr-xr-x 17 root root 0 Jan 1 1970 .. -rwxr-xr-x 1 root root 26982 May 17 2011 QTStart_Test -rw-r--r-- 1 root root 9852 Apr 8 2013 ads7843.ko -rw-r--r-- 1 root root 17978 Apr 8 2013 fpga_ctrl.ko -rw-r--r-- 1 root root 8150 Apr 8 2013 fpga_i2c.ko -rwxr-xr-x 1 root root 1484404 Apr 8 18:30 fpga_lcd_lx45.bin root@mityomapl138:/app# root@mityomapl138:/app# cd /dev root@mityomapl138:/dev# mknod /dev/fb0 c 29 0 root@mityomapl138:/dev# chgrp video fb0 root@mityomapl138:/dev# chmod g+w fb0 root@mityomapl138:/dev# ln -s fb0 fb root@mityomapl138:/dev# ls -l /dev/fb* lrwxrwxrwx 1 root root 3 Apr 8 18:24 /dev/fb -> fb0 crw-rw-r-- 1 root video 29, 0 Apr 8 18:23 /dev/fb0 root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/dev# cd /app root@mityomapl138:/app# insmod fpga_ctrl.ko fpga (null): loading the fpga_ctrl module. root@mityomapl138:/app# insmod ads7843.ko root@mityomapl138:/app# root@mityomapl138:/app# echo 1 > /sys/devices/fpga_ctrl/cmd root@mityomapl138:/app# echo 2 > /sys/devices/fpga_ctrl/cmd root@mityomapl138:/app# cat fpga_lcd_lx45.bin > /sys/devices/fpga_ctrl/image root@mityomapl138:/app# echo 3 > /sys/devices/fpga_ctrl/cmd input: ADS7843 Touchscreen as /devices/fpga_ctrl/1/input/input0 fpga fpga_ctrl: enable_irq_vector (0,0,1) root@mityomapl138:/app# root@mityomapl138:/app# cat /sys/devices/fpga_ctrl/state 4 : PROGRAMMED root@mityomapl138:/app# root@mityomapl138:/app# cat /sys/devices/fpga_ctrl/version PROGRAMMED FPGA Version : 01.01 FPGA Date : 0010-09-27 Base Module Version : 01.01 Base Module Date : 0010-09-27 root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# fbset -g 480 272 480 272 16 fbset: can't open '/dev/fb0': No such device root@mityomapl138:/app# root@mityomapl138:/app# ls /etc/dev* /etc/dev.tar /etc/device_table /etc/device_table-opkg root@mityomapl138:/app# root@mityomapl138:/app# rm /etc/dev.tar root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# opkg install qt4-embedded Package qt4-embedded (4.6.3-r25.1.6) installed in root is up to date. root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# ./QTStart_Test -qws QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 QScreenLinuxFb::connect: No such device Error opening framebuffer device /dev/fb0 root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# uname -a Linux mityomapl138 2.6.34-rc1-00003-g8bdeae6-dirty #9 PREEMPT Tue Nov 17 22:15:29 EST 2015 armv5tejl unknown root@mityomapl138:/app# root@mityomapl138:/app# root@mityomapl138:/app# cat /proc/fb root@mityomapl138:/app# root@mityomapl138:/app#