U-Boot SPL 2013.01.01 (Apr 23 2014 - 11:57:02)
BOARD : Critical Link MitySOM-5CSX Module
INFO : Watchdog enabled
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SDRAM: ECC Enabled
ALTERA DWMMC: 0


U-Boot 2013.01.01 (Apr 23 2014 - 11:57:17) Critical Link MitySOM-5CSX

CPU   : Altera SOCFPGA Platform
BOARD : Critical Link MitySOM-5CSX Module
I2C:   ready
DRAM:  1 GiB
MMC:   ALTERA DWMMC: 0
In:    serial
Out:   serial
Err:   serial
Net:   mii0

preboot reading MMC uBoot ENV data

** File not found /etc/uBootStatic.env **
## Info: input data size = 77 = 0x4D
** File not found /etc/uBoot.env **
## Info: input data size = 77 = 0x4D
...done
Hit any key to stop autoboot:  0
gpio: pin 28 (bank/mask = 0/0x10000000)
gpio: pin 28 (gpio 28) value is 0
gpio: pin 28 (bank/mask = 0/0x10000000)
gpio: pin 28 (gpio 28) value is 1
gpio: pin 0 (bank/mask = 0/0x00000001)
gpio: pin 0 (gpio 0) value is 1
gpio: pin 9 (bank/mask = 0/0x00000200)
gpio: pin 9 (gpio 9) value is 0
gpio: pin 9 (bank/mask = 0/0x00000200)
gpio: pin 9 (gpio 9) value is 1
7007184 bytes read in 2389 ms (2.8 MiB/s)
## Starting application at 0x3FF7F330 ...
## Application terminated, rc = 0xA
3495680 bytes read in 1192 ms (2.8 MiB/s)
18391 bytes read in 25 ms (717.8 KiB/s)
## Booting kernel from Legacy Image at 00007fc0 ...
   Image Name:   Linux-3.12.0-g456859b
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3495616 Bytes = 3.3 MiB
   Load Address: 00008000
   Entry Point:  00008000
## Flattened Device Tree blob at 00000100
   Booting using the fdt blob at 0x00000100
   XIP Kernel Image ... OK
OK
   Loading Device Tree to 03ff8000, end 03fff7d6 ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.12.0-g456859b (user@MitySOM-Dev) (gcc version 4.8.1 (GCC) ) #2 SMP Mon Jan 19 02:25:13 EST 2015
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Altera SOCFPGA, model: MitySOM-5CSX Altera SOCFPGA Cyclone V
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @80b80000 s11328 r8192 d13248 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait mem=512M
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512008K/524288K available (5266K kernel code, 261K rwdata, 1472K rodata, 347K init, 247K bss, 12280K reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
    lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x8069cba4   (6739 kB)
      .init : 0x8069d000 - 0x806f3c40   ( 348 kB)
      .data : 0x806f4000 - 0x80735650   ( 262 kB)
       .bss : 0x80735650 - 0x80773384   ( 248 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 17987 entries in 53 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x804c16c8 - 0x804c1720
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
NET: Registered protocol family 16
fpga bridge driver
DMA: preallocated 256 KiB pool for atomic coherent allocations
L310 cache controller enabled
l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x32460000, Cache size: 512 kB
syscon ffd05000.rstmgr: regmap [mem 0xffd05000-0xffd05fff] registered
syscon ffc25000.sdrctl: regmap [mem 0xffc25000-0xffc25fff] registered
syscon ff800000.l3regs: regmap [mem 0xff800000-0xff800fff] registered
syscon ffd08000.sysmgr: regmap [mem 0xffd08000-0xffd0bfff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
altera_hps2fpga_bridge fpgabridge.2: fpga bridge [hps2fpga] registered as device hps2fpga
altera_hps2fpga_bridge fpgabridge.2: init-val not specified
altera_hps2fpga_bridge fpgabridge.3: fpga bridge [lshps2fpga] registered as device lwhps2fpga
altera_hps2fpga_bridge fpgabridge.3: init-val not specified
altera_hps2fpga_bridge fpgabridge.4: fpga bridge [fpga2hps] registered as device fpga2hps
altera_hps2fpga_bridge fpgabridge.4: init-val not specified
bio: create slab <bio-0> at 0
FPGA Mangager framework driver
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Switched to clocksource timer1
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
arm-pmu arm-pmu: PMU:CTI successfully enabled
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
NTFS driver 2.1.30 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1000
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A
console [ttyS0] enabled
ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
brd: module loaded
at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write
cadence-qspi ff705000.spi: DMA NOT enabled
cadence-qspi ff705000.spi: master is unqueued, this is deprecated
m25p80 spi2.0: found n25q128a11, expected n25q00
m25p80 spi2.0: n25q128a11 (16384 Kbytes)
6 ofpart partitions found on MTD device spi2.0
Creating 6 MTD partitions on "spi2.0":
0x000000000000-0x000000040000 : "Preloader Image 0-3"
0x000000040000-0x000000050000 : "U-Boot Env"
0x000000050000-0x000000060000 : "DTB"
0x000000060000-0x0000000e0000 : "U-Boot"
0x0000000e0000-0x0000008e0000 : "Kernel"
0x0000008e0000-0x000001000000 : "Flash 0 jffs2 Filesystem"
m25p80 spi2.1: found n25q128a11, expected n25q00
m25p80 spi2.1: n25q128a11 (16384 Kbytes)
1 ofpart partitions found on MTD device spi2.1
Creating 1 MTD partitions on "spi2.1":
0x000000000000-0x000001000000 : "Flash 1 Filesystem"
cadence-qspi ff705000.spi: Cadence QSPI controller driver
dw_spi_mmio fff00000.spi: master is unqueued, this is deprecated
CAN device driver interface
c_can_platform ffc00000.d_can: invalid resource
c_can_platform ffc00000.d_can: control memory is not used for raminit
c_can_platform ffc00000.d_can: c_can_platform device registered (regs=a08d0000, irq=163)
c_can_platform ffc01000.d_can: invalid resource
c_can_platform ffc01000.d_can: control memory is not used for raminit
c_can_platform ffc01000.d_can: c_can_platform device registered (regs=a08d2000, irq=167)
stmmac - user ID: 0x10, Synopsys ID: 0x37
 Ring mode enabled
 DMA HW capability register supported
 Enhanced/Alternate descriptors
        Enabled extended descriptors
 RX Checksum Offload Engine supported (type 2)
 TX Checksum insertion supported
 Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 00221622 at 3 IRQ 0 (stmmac-0:03) active
usbcore: registered new interface driver usb-storage
s3c-hsotg ffb40000.usb: unable to find phy
s3c-hsotg ffb40000.usb: regs a08e0000, irq 160
s3c-hsotg ffb40000.usb: EPs:15
s3c-hsotg ffb40000.usb: dedicated fifos
mousedev: PS/2 mouse device common for all mice
rtc-ab18xx 0-0069: rtc core: registered ab1803 as rtc0
rtc-ab18xx 0-0069: 192 bytes nvram
i2c /dev entries driver
Synopsys Designware Multimedia Card Interface Driver
dwmmc_socfpga ff704000.dwmmc0: Using internal DMA controller.
dwmmc_socfpga ff704000.dwmmc0: Version ID is 240a
dwmmc_socfpga ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
mmc_host mmc0: Bus speed (slot 0) = 12500000Hz (slot req 400000Hz, actual 390625HZ div = 16)
dwmmc_socfpga ff704000.dwmmc0: 1 slots initialized
lp5562 0-0030: internal clock used
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
ThumbEE CPU extension supported.
Registering SWP/SWPB emulation handler
Waiting for root device /dev/mmcblk0p2...
dwmmc_socfpga ff704000.dwmmc0: data FIFO error (status=00000800)
mmc0: problem reading SD Status register.
mmc_host mmc0: Bus speed (slot 0) = 12500000Hz (slot req 12500000Hz, actual 12500000HZ div = 0)
mmc0: new high speed SDHC card at address 8883
mmcblk0: mmc0:8883 RF04G 3.69 GiB
 mmcblk0: p1 p2 p3
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 344K (8069d000 - 806f3000)
INIT: version 2.88 booting
Error opening /dev/fb0: No such file or directory
Starting udev
udevd[84]: starting version 182
Starting Bootlog daemon: bootlogd.
Configuring network interfaces... eth0: device MAC address 70:00:d5:ef:98:3c
udhcpc (v1.21.1) started
Sending discover...
libphy: stmmac-0:03 - Link is Up - 1000/Full
Sending discover...
Sending select for 10.40.20.200...
Lease of 10.40.20.200 obtained, lease time 604800
/etc/udhcpc.d/50default: Adding DNS 10.40.16.1
/etc/udhcpc.d/50default: Adding DNS 10.40.16.4
done.
Starting rpcbind daemon...rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
done.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
warning: /etc/sysctl.conf(70): invalid syntax, continuing...
warning: /etc/sysctl.conf(71): invalid syntax, continuing...
net.core.wmem_max = 12582912
net.core.rmem_max = 12582912
net.ipv4.tcp_rmem = 12582912 12582912 12582912
net.ipv4.tcp_wmem = 12582912 12582912 12582912
net.ipv4.tcp_window_scaling = 1
net.ipv4.tcp_timestamps = 1
net.ipv4.tcp_sack = 1
net.ipv4.tcp_no_metrics_save = 1
net.core.netdev_max_backlog = 50000
net.ipv4.tcp_mtu_probing = 1
net.ipv4.tcp_slow_start_after_idle = 0
Starting atd: OK
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
  generating ssh RSA key...
  generating ssh ECDSA key...
  generating ssh DSA key...
done.
creating NFS state directory: done
NFS daemon support not enabled in kernel
Starting system log daemon...0
Starting kernel log daemon...0
Starting Lighttpd Web Server: lighttpd.
2015-01-21 07:57:28: (/home/user/brdu/poky/build/tmp/work/cortexa9hf-vfp-neon-poky-linux-gnueabi/lighttpd/1.4.32-r0/lighttpd-1.4.32/src/log.c.118) opening errorlog '/www/logs/lighttpd.error.log' failed: Read-only file system
Starting crond: OK
Stopping Bootlog daemon: bootlogd.

Poky (Yocto Project Reference Distro) 1.5.3 mitysom-5csx /dev/ttyS0

mitysom-5csx login:
