Activity

From 02/17/2012 to 03/17/2012

10:49 PM Software Development: RE: OMAP GPIO: Hi Mike,
It turns out I didn't enable the Industrial Board I/O option in the kernel. After I enabled it (and enabl... Simon Wong
08:10 PM Software Development: RE: OMAP GPIO: Hi Simon,
I don't see anything wrong here, but you might want to ensure that the pin-mux configuration is setup fo... Michael Williamson
05:36 PM Software Development: OMAP GPIO: Hi,
I'm having trouble accessing the OMAP GPIO pins as detailed in the "MityARM-1810 PROFIBUS Dev Kit" documentati... Simon Wong
01:02 PM Software Development: 'Fast Boot' DSP: (Posted on behalf of a customer):
We need to boot the DSP fast (up and running code in less than 2 secs. ) and the... Gregory Gluszek

04:25 PM Software Development: RE: ftdi usb to serial drivers: Thanks Mike that worked. Scott Whitney
12:07 PM Software Development: RE: ftdi usb to serial drivers: You need to install mkimage on your linux machine.... Michael Williamson
12:02 PM Software Development: RE: ftdi usb to serial drivers: Tim,
Thanks for the help. I see the source in the code tree and also see why I couldn't see it in menuconfig. My p... Scott Whitney

05:25 PM Software Development: RE: ftdi usb to serial drivers: Scott
The FTDI serial drivers should be in the kernel source tree (as of kernel v 2.6.31)
Its the "USB FTDI Single ... Tim Iskander
05:14 PM Software Development: ftdi usb to serial drivers: Hello,
I want to access a device across the host USB that uses a FTDI chip to transmit serial data across the usb. ... Scott Whitney

04:10 PM Software Development: RE: StarterWare question ...: Also, as a followup question, the StarterWare examples are setting up the system for the evmOMAPL138. For instance, ... Tim Eastham
02:56 PM Software Development: StarterWare question ...: (posted on behalf of a customer)
For the starterware non-os method, I have built some of the starterware examples ... Thomas Catalino
10:16 AM Software Development: RE: Critical Link Package locations?: At the moment, we don't provide customized packages. The mityomapl138 location was generated during the bitbake buil... Michael Williamson
10:12 AM Software Development: Critical Link Package locations?: (posted on behalf of a customer)
What are the updated feed addresses for the critical link packages?

(these ar... Thomas Catalino

06:11 PM Software Development: RE: about boot: Mike,
Thank you very much. I understand. shengyou gao
04:51 PM Software Development: RE: about boot: The EXT_BOOT# signal drives a small mux circuit on the SOM that changes the boot strap pull-up/pull-down options on t... Michael Williamson
04:56 PM PCB Development: RE: FPGA no-connects for 45 size FPGA on MityDSP-L138F: The bare board PCB for the two variants of the SOM are identical, the only difference is the BOM used for assembly. ... Michael Williamson

08:28 AM Software Development: about boot: I wonder how the boot mode switch from SPI1 to UART1 using EXT_BOOT# signal? Thank very much. shengyou gao

08:47 AM PCB Development: FPGA no-connects for 45 size FPGA on MityDSP-L138F: (Posted on behalf of a customer)
We have done a design using the MityDSP-L138F SOM. I tried avoiding using the pin... Thomas Catalino

05:01 PM Software Development: RE: Hello World Starter Guide Permission Issue: You rock! It was the file that was the problem. I found the executable and it worked. Thanks! Tim Eastham
04:50 PM Software Development: RE: Hello World Starter Guide Permission Issue: Hi Tim,
First, the reason you're getting the "-sh: ./hello.o: Permission denied" error is because the file you are... Gregory Gluszek
04:25 PM Software Development: Hello World Starter Guide Permission Issue: I am a newbie to the arm environment and quite green on linux as well. I have been going through the hello world exa... Tim Eastham

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)