Activity
From 04/12/2012 to 05/11/2012
05/09/2012
- 04:22 PM Software Development: RE: Starterware EMIFA to FPGA example code
- Hi Mike,
In the case of 32 bit transfers as described above -
Can you tell me which 16-bit value is transferred ...
05/08/2012
- 04:55 PM FPGA Development: RE: Programming the FPGA
- Appreciate the feedback on the wiki page. I've updated it per your comments.
-Mike
- 04:40 PM FPGA Development: RE: Programming the FPGA
- Thanks! That worked. An even better solution than the bootfpga solution.
I was basing what I did on the wiki pag... - 03:03 PM FPGA Development: RE: Programming the FPGA
- Hi Tim / Emmett,
Did you remember to saveenv? (just checking)
A couple of things:
You might want to avoid u... - 02:15 PM FPGA Development: RE: Programming the FPGA
- Emmett and I were able to get the DONE LED by calling loadfpga after the loadb 0xc0700000. The problem is that when ...
- I have read both forum entries of the same name.
The first one seems to be most applicable, since I have the MityARM...
05/02/2012
- 07:46 AM Software Development: RE: uPP/DMA registers
- We have demonstrated capturing as high as 100 MB/sec using UPP in 180 MB blocks without issue. So it's feasible. If...
- 03:10 AM Software Development: RE: uPP/DMA registers
- @Mike
Thanks for the detailed answer. We are only using the AM1808 as an embedded video server for the stream comi...
04/30/2012
- 10:12 AM Software Development: RE: uPP/DMA registers
- Shahzad, I have not found uPP drivers for the ARM in linux. My suggestion in developing them is to read the TI uPP ...
04/29/2012
- 06:25 PM Software Development: RE: TI C6EZAccel library with MityDSP Platform - OmapL138
- Hi Michele,
If you would like to use the full TI DVSDK (including C6EZAccel), you can install it from TI (along wi... - Dear Sirs,
does anybody there managed to install and use the C6EZAccel library for the OMAPL138 processor, using the...
04/28/2012
- 10:19 AM Software Development: RE: uPP/DMA registers
- If you are not using the on-Board NAND in your design (e.g., booting to a RAMDISK or off of MMC or something), then t...
- 09:52 AM Software Development: RE: uPP/DMA registers
- Hi Mike,
Thanks for the prompt reply. Actually the data stream is from an H.264 encoder in an FPGA, so im not sure... - 08:18 AM Software Development: RE: uPP/DMA registers
- Hello Shahzad,
Unfortunately, there is still no UPP driver available. Have you looked at pushing the data in usin... - 04:11 AM Software Development: RE: uPP/DMA registers
- Hi Mike,
I am looking for a uPP driver for linux and I was searching around when I came across this thread. I know...
04/26/2012
- 12:21 AM Software Development: RE: FS Corruption due to dropping power
- Hi Mike,
Thanks for the reply. This is reasuring that it is a FS corruption problem. I have instigated a read onl...
04/25/2012
- 12:57 PM Software Development: RE: Starterware EMIFA to FPGA example code
- Hi Emmett,
Are you using linux or starterware? On starterware, if you are launching from u-Boot (which configures... - Hello,
I have used your "EMIFA_iface" VHDL example to make a simple FPGA to test by reading/writing to registers r...
04/13/2012
- 06:31 PM PCB Development: RE: RTC Battery Drain
- Hi,
Wanted to follow up on this. We have seen RTC battery drainage, but at the time we looked at it we were using... - 06:28 PM Software Development: RE: FS Corruption due to dropping power
- Hi Keith,
I have seen these symptoms before, and I'm pretty sure it's filesystem corruption related (I suspect ude...
04/12/2012
- Hi, We are developing a system where the user is unlikely to power down gracefully, even if asked to do so and ultima...
Also available in: Atom
Go to top
