Activity
From 04/24/2012 to 05/23/2012
05/21/2012
- 09:48 AM Software Development: RE: Warning messages when running DSP Hello World
- Hi François,
We've seen this issue before, but haven't been able to track it down yet. It seems to be benign, so ...
05/19/2012
- 10:40 AM Software Development: RE: Downloading and Installing the Virtual Machine?
- Thanks Mike!
- 06:56 AM Software Development: RE: Downloading and Installing the Virtual Machine?
- I think there is a link to the VM appliance, I'll try to get someone to post that for you.
There is a newer image,... - Hi Folks,
The Wiki says the current version of the VM appliance can be downloaded, but I can't find a download lin...
05/18/2012
- Hi,
I was able to walk-through the DSP_Hello_World tutorial. The test applications seems to run well until arm app... - 07:47 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
Thanks, that did the job.
The bad news is that 3.2.0 does not have KS8995 support. It seems that this only... - 06:22 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- I don't think your compiled correctly or uploaded the correct uImage to the machine.
The "Image Name: Linux-2.6.34... - 04:34 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I have downloaded the branch as above but when i compile i get the following:-
Image Name: Linux-2.6.34-... - 03:49 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I have found a branch 'mitydsp-linux-v3.2', which I assume is the one you referred to, which I am downloading...
05/17/2012
- 03:46 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
Thank you for your assistance. I would like to look at the version 3.2, so if you could let me know how to ac... - 09:50 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Hi Charlie,
I guess the first question is, "what do you want to do with the switch?". As I mentioned before, we h... - 09:22 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I am the customer who submitted this post. I had a problem with logging on which is why Tom posted this for m...
05/16/2012
- 02:42 PM Software Development: RE: MACHINE type for the MDK ...
- MACH_TYPE_MITYOMAPL138, 2650 (decimal).
The machine type is registered and can be found in the autogerated machine... - (posted on behalf of a customer)
The Linux which I installed is the latest available with MDK-2-12, version Angstr... - 02:38 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- We have had customers successfully integrate both an KSZ8893MBL switch and the KSZ8895MAI switch with the MityDSP-L13...
- (posted on behalf of a customer)
Have you, or do you know of anyone who has got a KSZ8995MA Ethernet Switch chip t...
05/15/2012
- 08:40 AM Software Development: RE: Starterware EMIFA to FPGA example code
- Hi Emmet,
The processor will write or read the first (lower address) 16 bits first, followed by the upper 16 bits ...
05/09/2012
- 04:22 PM Software Development: RE: Starterware EMIFA to FPGA example code
- Hi Mike,
In the case of 32 bit transfers as described above -
Can you tell me which 16-bit value is transferred ...
05/08/2012
- 04:55 PM FPGA Development: RE: Programming the FPGA
- Appreciate the feedback on the wiki page. I've updated it per your comments.
-Mike
- 04:40 PM FPGA Development: RE: Programming the FPGA
- Thanks! That worked. An even better solution than the bootfpga solution.
I was basing what I did on the wiki pag... - 03:03 PM FPGA Development: RE: Programming the FPGA
- Hi Tim / Emmett,
Did you remember to saveenv? (just checking)
A couple of things:
You might want to avoid u... - 02:15 PM FPGA Development: RE: Programming the FPGA
- Emmett and I were able to get the DONE LED by calling loadfpga after the loadb 0xc0700000. The problem is that when ...
- I have read both forum entries of the same name.
The first one seems to be most applicable, since I have the MityARM...
05/02/2012
- 07:46 AM Software Development: RE: uPP/DMA registers
- We have demonstrated capturing as high as 100 MB/sec using UPP in 180 MB blocks without issue. So it's feasible. If...
- 03:10 AM Software Development: RE: uPP/DMA registers
- @Mike
Thanks for the detailed answer. We are only using the AM1808 as an embedded video server for the stream comi...
04/30/2012
- 10:12 AM Software Development: RE: uPP/DMA registers
- Shahzad, I have not found uPP drivers for the ARM in linux. My suggestion in developing them is to read the TI uPP ...
04/29/2012
- 06:25 PM Software Development: RE: TI C6EZAccel library with MityDSP Platform - OmapL138
- Hi Michele,
If you would like to use the full TI DVSDK (including C6EZAccel), you can install it from TI (along wi... - Dear Sirs,
does anybody there managed to install and use the C6EZAccel library for the OMAPL138 processor, using the...
04/28/2012
- 10:19 AM Software Development: RE: uPP/DMA registers
- If you are not using the on-Board NAND in your design (e.g., booting to a RAMDISK or off of MMC or something), then t...
- 09:52 AM Software Development: RE: uPP/DMA registers
- Hi Mike,
Thanks for the prompt reply. Actually the data stream is from an H.264 encoder in an FPGA, so im not sure... - 08:18 AM Software Development: RE: uPP/DMA registers
- Hello Shahzad,
Unfortunately, there is still no UPP driver available. Have you looked at pushing the data in usin... - 04:11 AM Software Development: RE: uPP/DMA registers
- Hi Mike,
I am looking for a uPP driver for linux and I was searching around when I came across this thread. I know...
04/26/2012
- 12:21 AM Software Development: RE: FS Corruption due to dropping power
- Hi Mike,
Thanks for the reply. This is reasuring that it is a FS corruption problem. I have instigated a read onl...
04/25/2012
- 12:57 PM Software Development: RE: Starterware EMIFA to FPGA example code
- Hi Emmett,
Are you using linux or starterware? On starterware, if you are launching from u-Boot (which configures... - Hello,
I have used your "EMIFA_iface" VHDL example to make a simple FPGA to test by reading/writing to registers r...
Also available in: Atom
Go to top
