Activity
From 12/15/2014 to 01/13/2015
01/13/2015
- 04:30 PM Software Development: RE: u-boot problem
- Without the serial converter it works.
The board has come to life!
Thank !!! - 09:25 AM Software Development: RE: u-boot problem
- Could you verify that the BOOTME message is sent by the l138 when you power it while holding the boot button? The out...
- 09:21 AM Software Development: RE: u-boot problem
- You should not need to do that if you are getting past u-Boot and trying to boot the kernel.
If you are getting an... - 09:19 AM Software Development: RE: u-boot problem
- Unfortunately, does not help. The message of the utility is following:
D:\...\MityDSP\sfh_ubl_072111>sfh_OMAP-L138... - 09:01 AM Software Development: RE: u-boot problem
- Does this help?
[[Reprogramming a Dead Board]] - 07:44 AM Software Development: RE: u-boot problem
- Hi Mike.
After manipulations in accord https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Progr... - 07:09 AM Software Development: RE: u-boot problem
- Post the complete text and your u-Boot environment.
Typically, this message is because the kernel cannot locate a ... - Hi,
After power on board MityDSP-L138F the download stops with the message " Kernel panic - not syncing: No init fou...
01/12/2015
- 05:48 AM FPGA Development: RE: FPGA programming
- Thank for your reply Mike.
Is it possible to write an image FPGA through СОМ1 on MityDSP? Whether it is possible t...
01/10/2015
- 09:17 AM FPGA Development: RE: FPGA programming
- Once you have a bit file that you like you can run the promgen tool to create the binary image to load per this wiki ...
- Hi,
I have board L138-FI-236-RL.
Developed in Xilinx ISE the design fine works on FPGA at use ISE iMPACT.
Please...
01/09/2015
- 05:48 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- Thank you, you where spot, it solved the issue with only having one pin high at a time.
The following works
mp...
01/08/2015
- 09:18 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- Also, you should not be calling the destructor. This line is not OK:...
- 08:29 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- The driver could be rewritten to contain a shadow mask of the desired output register, but that is not the current im...
- 08:28 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- The code for the DSP GPIO control does a read modify write. It Reads the input state of the entire bank, masks the v...
- 08:04 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- Not sure what you mean with input ?,
both are mapped in the VHDL code as output. and set as output with SetPinDirect... - 07:52 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- Do you have the inputs of the GPIO core for offsets 0 and 1 connected in you FPGA design?
- 04:22 AM Software Development: RE: Simple Code/Doc for FPGA toggle of GPIO from DSP
- Hi
If i want to toggle both pin 7 and pin 15 at the same time i have an issue (both work independently). Pin 7 goe... - Hi All,
I try to figure out how to serve an interrupt in the DSP code and how to register an ISR for a FPGA interr...
01/05/2015
- 07:08 PM FPGA Development: RE: Programming the FPGA
- Hi
What was the solution to the last problem (add source error)? I get the same warning when trying to add pwm.ngc...
12/23/2014
- Hi im trying to toggle a pin in the FPGA(busy/awake LED would do for now) from the DSP. Is there a doc(howto) describ...
12/22/2014
- 06:27 AM Software Development: RE: DSP/BIOS issue MityDSP-L138
- Thank Alex for your answer.
I think a problem was in incorrect PINMUX for UART-1.
My design works fine for UART-0...
12/18/2014
- 10:41 PM Software Development: RE: DSP/BIOS issue MityDSP-L138
- Oleh,
Can you please share some more details about this issue if it is still occurring?
It looks to me like Ubo...
Also available in: Atom
Go to top
