Activity

From 08/17/2018 to 09/15/2018

01:32 PM Software Development: RE: Yocto MDK Status: Thanks Tom. Jonathan Cormier
12:40 AM Software Development: RE: Yocto MDK Status: FYI... have made the following changes to the recipes as to update fetching the proper sources. For vim it's a differ... Tom Riddle

11:06 PM Software Development: RE: Yocto MDK Status: Hi, well it was easier then trying to fix the two repo failures, (which I will do)... just running bitbake again with... Tom Riddle
10:04 PM Software Development: RE: Yocto MDK Status: Tom Riddle wrote:
> Hi Jonathan,
>
> We open a shell, go to yocto-archives dir, set the env
>
> > source oe-i... Jonathan Cormier
07:36 PM Software Development: RE: Yocto MDK Status: Hi Jonathan,
We open a shell, go to yocto-archives dir, set the env
> source oe-init-build-env
then execute... Tom Riddle

06:21 PM Software Development: RE: Yocto MDK Status: Could you provide a log of your bitbake command plus output in an attached file? Jonathan Cormier
06:10 PM Software Development: RE: Yocto MDK Status: Hi Folks... any feedback on where the image might be? Thanks, Tom Tom Riddle
03:18 PM PCB Development: RE: OMAP L138 HPI: Unfortunately during my initial review of the modules with and without FPGA I confused the RESETOUT (T17) pin connect... Alexander Block
09:05 AM PCB Development: RE: OMAP L138 HPI: Thank you.
I was able to check the connection information between FPGA and L138.
Could you tell me the pin wiri... Hisato Seki

11:12 PM PCB Development: RE: OMAP L138 HPI: You can find the pin-out between the FPGA and the OMAP-L138 processor of the module in the Carrier Board Design Guide... Alexander Block
01:53 AM PCB Development: RE: OMAP L138 HPI: Thank you for your reply.
Sorry, I missed BALL R16, R17.
I found that a board with FPGA(MityDSP-L138F) is neces... Hisato Seki
04:37 PM Software Development: RE: Yocto MDK Status: Hi Bob, thanks for the quick response, I'll start playing with the recipe.
On the rootfs question, can't seem to ... Tom Riddle
04:19 PM Software Development: RE: Yocto MDK Status: Tom Riddle wrote:
> Thanks Jonathan I will give that a try, in the meantime there are a few other questions.
>
> ... Bob Duke
03:59 PM Software Development: RE: Yocto MDK Status: Thanks Jonathan I will give that a try, in the meantime there are a few other questions.
So we have a 3.2 kernel h... Tom Riddle

08:15 PM PCB Development: RE: OMAP L138 HPI: I'm not sure that we've used the UHPI interface in any designs nor am I aware of any customers that have utilized the... Alexander Block
08:32 AM PCB Development: OMAP L138 HPI: I am looking for a board that can use HPI function of DSP of OMAP L138.
Is it possible to operate HPI using MityDSP-... Hisato Seki

08:22 PM Software Development: RE: Yocto MDK Status: It looks like the vim repo has been moved. googlecode.com is no longer a valid url. Looking at more recent "vim rec... Jonathan Cormier
06:44 PM Software Development: RE: Yocto MDK Status: Hi, One last question... I built with "-k" to get past these two fetch errors,
Summary: 2 tasks failed:
/expor... Tom Riddle
04:02 PM Software Development: RE: Yocto MDK Status: Hi, thanks... suspected that was the case but didn't know where the setting was at. It successfully fetched and is mo... Tom Riddle
03:33 PM Software Development: RE: Yocto MDK Status: Thanks for the extra info. wanda.syr.criticallink.com is an internal server, CL_SOURCE_GIT_HOST should point to supp... Jonathan Cormier

09:24 PM Software Development: RE: Yocto MDK Status: Ok, Will try again... hope I can get an answer to the network question... it appears to fail at trying to fetch the f... Tom Riddle

05:38 PM Software Development: RE: Yocto MDK Status: Hi, So in the building of the yocto-archive it seems to get pretty far until these errors appear
ERROR: Function f... Tom Riddle

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)