Mity CPU Platforms » ARM9 Based QNX Platforms

11/15/2011

03:30 PM Software Development: RE: OMAP I2C

Yes, it works (thanks):... Mark Lyon

03:24 PM Software Development: RE: OMAP I2C

Mark,
I probably should have used O_RDWR instead of O_RDONLY. I am surprised it worked with just O_RDONLY.
The ... John Pruitt

03:17 PM Software Development: RE: OMAP I2C

Interesting. We were using Qnx's demo which uses DCMD_I2C_RECV rather than DCMD_I2C_SENDRECV so that was part of the... Mark Lyon

01:27 PM Software Development: RE: OMAP I2C

I am attaching a test program that was used on a board to read the factory config information using i2c0.
The outp... John Pruitt

11/14/2011

05:13 PM Software Development: RE: OMAP I2C

Can you try to get the sample program that the qnx engineer used?
Thanks.
John Pruitt

09:47 AM Software Development: RE: OMAP I2C

An engineer from QNX hooked a scope to I2C0 lines on their EVM board and sent the sendrecv command. They were able to... Mark Lyon

11/11/2011

03:04 PM Software Development: RE: OMAP I2C

IFor what it is worth, it should be noted that the i2c accesses in the startup code and in the i2c_get utility are do... John Pruitt

11/03/2011

02:08 PM Software Development: RE: FPGA Driver

I have posted a new BSP which has a fixed FPGA driver and fix to the timer routines so the clock period can be change... John Pruitt

11/01/2011

09:12 AM Software Development: RE: OMAP I2C

Mark,
I2C0 is not something that needs to be turned on. It is used internally in the startup code to read configur... John Pruitt

09:00 AM Software Development: RE: OMAP I2C

It looks like neither I2C driver is started by default.
We are trying to use I2C0
There is an error generated if we... Mark Lyon

10/28/2011

02:44 PM Software Development: RE: FPGA Driver

Mark,
The files under /dev/fpga are not intended to be executed. They are intended to be opened and then read from... John Pruitt

02:27 PM Software Development: RE: FPGA Driver

Tried that - now I'm having a very strange, possibly unrelated problem where the files created under /dev/fpga are cr... Mark Lyon

10/27/2011

05:04 PM Software Development: RE: FPGA Driver

Mark,
These is a mistake in the fpga driver as provided. It is printing out the virtual addresses for the cores in... John Pruitt

03:35 PM Software Development: RE: FPGA Driver

Understood. I have a memory block in the FPGA that I was able to examine using mmap_device_memory().
The offset wa... Mark Lyon

03:29 PM Software Development: RE: FPGA Driver

Mark,
The 5 fpga device files (cmd, image, state, version, and devices) are for loading an image into the fpga and... John Pruitt

02:51 PM Software Development: RE: FPGA Driver

I have the FPGA driver loaded, with the FPGA mapped into 0x66000000.
If I want to access the FPGA for a user applica... Mark Lyon

10/26/2011

03:57 PM Software Development: RE: Pin MUX

Just saw a signal out of the port - thanks. It may have been a conflict with the I2C or something else we tried along... Mark Lyon

03:19 PM Software Development: RE: Pin MUX

Mark,
I have tried using a scope on an INDIO board (80-000268RI-2 rev. B, serial number 110765) with a module (L13... John Pruitt

07:45 AM Software Development: RE: Pin MUX

We are using RS-232 at TTL levels, so that is not a problem.
We had done all the steps you outlined and we are not s... Mark Lyon

10/25/2011

04:32 PM Software Development: RE: Pin MUX

Mark,
I do not know of any qnx code that has been used with this port. I have been talking with the hardware guys ... John Pruitt