Activity
From 01/30/2012 to 02/28/2012
02/28/2012
- (Posted on behalf of a customer)
We have done a design using the MityDSP-L138F SOM. I tried avoiding using the pins on the FPGA that are not connected in the larger variant, but I was not succesfull, meaning I accidently used two of t...
02/22/2012
- TE 05:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Hello World Starter Guide Permission Issue
- You rock! It was the file that was the problem. I found the executable and it worked. Thanks!
- GG 04:50 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Hello World Starter Guide Permission Issue
- Hi Tim,
First, the reason you're getting the "-sh: ./hello.o: Permission denied" error is because the file you are trying to execute does not have execute permissions set. (You can see a file's permissions using the "ls -l" command an... - I am a newbie to the arm environment and quite green on linux as well. I have been going through the hello world example located here (http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Starter_Guide). I have worked m...
02/16/2012
- (posted on behalf of a customer)
For the MityDSP-l138F, I noticed the drill hole for the standoff in the Altium file (for the Industrial IO board) is acutally about 1780mils from the center of the DIMM Connector. As oppose to 2in - ....
02/14/2012
-
03:24 PM
ARM9 Based QNX Platforms
Software Development: RE: Running SYS/BIOS on the ARM MityDSP-L138 module
- Dave,
I've been over on the e2e forum for a couple weeks getting our current DSP
running on the OMAP137. TI has confirmed that their Network Development Package
does not support the 137. So I'll need to get a 138 dev board and h... - DS 03:14 PM ARM9 Based QNX Platforms Software Development: RE: Running SYS/BIOS on the ARM MityDSP-L138 module
- This is something that we haven't done yet.
TI has some info on this: here are some links that may be worth exploring:
TI's starterware:
http://processors.wiki.ti.com/index.php/StarterWare
and SYSBIOS wiki:
http://processors.w... -
11:21 AM
ARM9 Based QNX Platforms
Software Development: Running SYS/BIOS on the ARM MityDSP-L138 module
- Hi,
I'm currently using a Spectrum Digital's OMAP-L137 eval board to run some older DSP code and I'd like to have the ARM collect Ethernet
data via TI's NDK and pass it through to the DSP. Because there seems to be no underlyin...
02/08/2012
- DB 11:51 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions
- Thanks Mike,
I have Rev 1/Document Revision: Draft – MityDSP-Pro Rev. B dated Nov 15th 2009 of the design guide and it wasn't in that. I guess there must be a later version. Is the only place to get the documents on the web site were ... - MW 10:58 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions
- Hi Doug, dorry for the delay.
The information you need should be in the MityDSP-Pro Carrier board design guide, I am attaching a copy of the figure here. Is this what you need?
-Mike
!MityDSP-PRO-Aux_Connector_Location.png! - DB 10:48 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions
- I would like to get a reply to my question. I am finishing up my layout and need to place the connector.
Thanks,
Doug
02/06/2012
- (posted on behalf of a customer for the MityARM-1808F module)
Any advice on how to connect your EMIF interface to an AXI bus (a Xilinx FPGA core standard) in the FPGA would be appreciated.
02/03/2012
- It is recommended to use the AUX I/O connector on the MityDSP-Pro on carrier board designs but I can't seem to find any documentation on the location of the connector. Please let me know if it is called out in any of the documentation. I...
02/01/2012
- (posted on behalf of a customer)
A quick question for you, or perhaps someone else on your team, regarding
the RTC on the L138 modules and the profibus development kit battery:
We have noticed that the RTC batteries have been run...