Mity CPU Platforms

01/16/2017

AB 05:17 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD

Ben,
Thank you for providing the device specific details.
I wanted to let you know that on Friday 1/13/2017 I sent you an e-mail requesting additional company specific information, that I wasn't sure you would want to post on the f... Alexander Block

01/13/2017

BF 08:44 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD

Thanks. Today we tested two kits against each other (we switched the DevKit and modules). The results were, that the development boards were OK, but one Cyclone V SOC module (this was mine) is not booting. The orange LED is permanently O... Benjamin Fischer

MW 07:52 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD

Hi Benjamin,
I am forwarding this on to our support team, but it sounds like there may be an issue with the DevKit card or module. If I understand, you are able to use the same SD card on different units and some units work and this ... Michael Williamson

BF 07:35 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD

On other devices my image is working... It seems that I got a newer module (noticed some small differences on the PCB). ID: 5CSXFC6C6U23I7N Benjamin Fischer

01/12/2017

JC 02:41 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA - Loading via CPU

I don't understand the difference between this question and your last question. https://support.criticallink.com/redmine/boards/10/topics/5138
The programming guide from which you grabbed the above paragraph, includes the two ways tha... Jonathan Cormier

JA 12:45 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Programming the FPGA - Loading via CPU

Hi, Good Day, I am trying to load the FPGA via CPU, but I would like to know: How can I configure the slave select mode in the FPGA?. I read the Xilinx Spartan-6 configuration guide, but it is not enough clear.
"The FPGA has been con... Jesus Alejandro Alvarez Trejo

JA 11:15 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: Communication between AM1810 ARM Microprocessor For PROFIBUS and Spartan 6

Hello, Good Day, I have the MitySOM-1810F PROFIBUS Development kit which includes the AM1810 ARM Microprocessor For PROFIBUS and Spartan 6, I would like to know how I can communicate both devices, I mean, what kind of protocol and how im... Jesus Alejandro Alvarez Trejo

MW 11:08 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA

Take a look at the [[Programming the FPGA]] for information about programming the FPGA. The wiki page on this web site has a bunch of information to get started.
If you want to program with JTAG via a Xilinx emulator pod, you can do ... Michael Williamson

JA 11:05 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: Programming the FPGA

Hello, Good Day, I have the MitySOM-1810F PROFIBUS Development kit, I am starting to use it and I do not know how load the FPGA, I would like to know if I need a special connector or if I could use other method to load the FPGA. Jesus Alejandro Alvarez Trejo

BF 03:52 AM MitySOM-5CSX Altera Cyclone V Software Development: 5CSX-H6-42A Dev.Kit does not boot from SD

Hi guys,
this struggles me for a few days now. I got the mentioned Dev-Kit, read a lot in Rocketboards and this Wiki, and so I wanted to try it out by myself.
So I installed the virtual-machine, compiled my Preloader and U-Boot to c... Benjamin Fischer

01/08/2017

AA 06:11 AM MitySOM-5CSX Altera Cyclone V Software Development: accesing wiki and forums via https problem

When trying to access wiki and forums i get
An error occurred during a connection to support.criticallink.com. The OCSP server suggests trying again later. Error code: SEC_ERROR_OCSP_TRY_SERVER_LATER
The page you are trying to... aggelis aggelis