Mity CPU Platforms

04/01/2023

05:50 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

I use the standard devkit. When I had problems with the SD card (for example, bad partition), I got these messages:
... Vadym Kolesnyk

03/31/2023

09:30 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

If this is a custom baseboard without the card detect hooked up. Then this could also happen.
For an example of d... Jonathan Cormier

09:24 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

That is unexpected. Your boot log looks like everything is correct. It looks similar to if you had no sdcard plugged... Jonathan Cormier

04:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

I made rootfs on an SD card according to this wiki page (https://support.criticallink.com/redmine/projects/arm9-platf... Vadym Kolesnyk

11:14 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Mike,
Ah, makes sense.
For the time being I'll stick with controlling the clock frequency with Linux.
Thank... Kim Nielsen

03/29/2023

07:03 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
I think the reason why the uBoot Critical Link publishes is using 300 MHz is because the Revision 1 silico... Michael Williamson

03/27/2023

02:12 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Alright.
Is there is no way to change the default frequency from 300Mhz to e.g. 372MHz with U-Boot?
As far as I ... Kim Nielsen

02:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
I think the issue is that the voltage scaling needs to be done to default
to a higher frequency.
The P... Michael Williamson

02:00 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

I don't see an obvious default frequency config in the kernel, I'd guess that it stays with whatever frequency was se... Jonathan Cormier

01:44 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

I actually got another question.
By default, the cpu frequency seems to always be 300 MHz.
Is this value hardco... Kim Nielsen

03/24/2023

05:24 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Kim Nielsen wrote in message#6283:
> It's our own "experimental" kernel.
> It seems to be working now. The issue wa... Jonathan Cormier

12:21 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

It's our own "experimental" kernel.
It seems to be working now. The issue was that the pll0 registers were apparentl... Kim Nielsen

03/23/2023

01:37 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Where is the 4.19 kernel based from? It doesn't appear to have working cpufreq. Jonathan Cormier

07:17 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Mike & Jonathan,
Thank you for the fast reply :-)
I have the following frequencies available according to th... Kim Nielsen

03/22/2023

09:25 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim, What kernel version are you using? Testing this on our released 3.2 kernel appears to be working for me.
... Jonathan Cormier

05:23 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
What do you get when you dump out the scaling_available_frequencies (I don't remember the exact name off t... Michael Williamson

03:14 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Increasing CPU clock OMAPL138

Hi,
I'm using a "L138-FI-236-RL" SOM board with SYS/BIOS running on the DSP and Linux on the ARM.
The Linux is bu... Kim Nielsen

03/13/2023

07:19 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Building Root Filesystem 18.1 - Python Issue

Jose,
You're correct, this is an issue with poky-crops updating their docker to contain the new 4.1 toolchain for ... Mike Fiorenza

06:57 PM MitySOM-5CSX Altera Cyclone V Software Development: Building Root Filesystem 18.1 - Python Issue

Hello,
I am trying to follow the guide for Building the Root Filesystem but I keep getting this error after trying ... Jose Berlioz

03/08/2023

06:58 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: HPS RGMII EMAC connection to external MAC inference

Thank you for the update, it was great to meet you today!
Tom Thomas Catalino

05:51 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: HPS RGMII EMAC connection to external MAC inference

UPDATE:
Adding 22Ω series termination resistors on the RX RGMII traces leading into the mitySOM module solved this... S. D.