Mity CPU Platforms » MitySOM-335x (ARM Cortex-A8 Based Products)

U-Boot# bootm

## Booting kernel from Legacy Image at 82000000 ...

   Image Name:   Linux-3.2.0-00351-gb80917e-dirty

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    3737096 Bytes = 3.6 MiB

   Load Address: 80008000

   Entry Point:  80008000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[    0.000000] Linux version 3.2.0-00351-gb80917e-dirty (mitydsp@mitydsp-dev) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #24 Mon Jan 25 15:21:36 EST 2016

[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine: mitysom335x

[    0.000000] Memory policy: ECC disabled, Data cache writeback

[    0.000000] AM335X ES2.1 (sgx neon )

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048

[    0.000000] Kernel command line: console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=8,4096 noinitrd rootfstype=ubifs rootwait=1 ip=none

[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Memory: 512MB = 512MB total

[    0.000000] Memory: 511060k/511060k available, 13228k reserved, 0K highmem

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)

[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

[    0.000000]       .text : 0xc0008000 - 0xc0764000   (7536 kB)

[    0.000000]       .init : 0xc0764000 - 0xc07a1000   ( 244 kB)

[    0.000000]       .data : 0xc07a2000 - 0xc083a928   ( 611 kB)

[    0.000000]        .bss : 0xc083a94c - 0xc087bf14   ( 262 kB)

[    0.000000] NR_IRQS:396

[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[    0.000000] Total of 128 interrupts on 1 active controller

[    0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz

[    0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz

[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms

[    0.000000] Console: colour dummy device 80x30

[    0.000061] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)

[    0.039062] pid_max: default: 32768 minimum: 301

[    0.039184] Security Framework initialized

[    0.039276] Mount-cache hash table entries: 512

[    0.039611] CPU: Testing write buffer coherency: ok

[    0.040313] devtmpfs: initialized

[    0.059631] omap_hwmod: pruss: failed to hardreset

[    0.060821] print_constraints: dummy:

[    0.061157] NET: Registered protocol family 16

[    0.063140] OMAP GPIO hardware version 0.1

[    0.065521] omap_mux_init: Add partition: #1: core, flags: 0

[    0.067474] Configuring I2C Bus 1

[    0.067565]  omap_i2c.2: alias fck already exists

[    0.067749] Configuring I2C Bus 2

[    0.067810]  omap_i2c.3: alias fck already exists

[    0.068664] Registering mcspi 1 [2]

[    0.068695]  omap2_mcspi.1: alias fck already exists

[    0.068908] Registering mcspi 2 [2]

[    0.068939]  omap2_mcspi.2: alias fck already exists

[    0.069244]  edma.0: alias fck already exists

[    0.069274]  edma.0: alias fck already exists

[    0.069274]  edma.0: alias fck already exists

[    0.072265] baseboard_init [MitySOM-335x Frantec AEC]...

[    0.072479] MitySOM-335x Frantec AEC: SPI baseboard_setup_enet

[    0.073425] MitySOM-335x Frantec AEC: SPI baseboard_setup_usb

[    0.073760] MitySOM-335x Frantec AEC: SPI baseboard_setup_dvi

[    0.074096]  da8xx_lcdc.0: alias fck already exists

[    0.074493] MitySOM-335x Frantec AEC: SPI baseboard_setup_can

[    0.074554]  d_can.1: alias fck already exists

[    0.074768] MitySOM-335x Frantec AEC: SPI baseboard_setup_spi0_devices

[    0.074829] MitySOM-335x Frantec AEC: SPI baseboard_setup_uarts

[    0.096923] bio: create slab <bio-0> at 0

[    0.098876] SCSI subsystem initialized

[    0.100463] usbcore: registered new interface driver usbfs

[    0.100738] usbcore: registered new interface driver hub

[    0.100921] usbcore: registered new device driver usb

[    0.101074] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3

[    0.101379] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0

[    0.119110] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz

[    0.139068] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz

[    0.139953] tps65910 3-002d: JTAGREVNUM 0x1

[    0.142303] print_constraints: VRTC:

[    0.143737] print_constraints: VIO: at 1500 mV

[    0.146026] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal

[    0.148284] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal

[    0.149261] print_constraints: VDD3: 5000 mV

[    0.150695] print_constraints: VDIG1: at 1800 mV

[    0.152069] print_constraints: VDIG2: at 1800 mV

[    0.153503] print_constraints: VPLL: at 1800 mV

[    0.154907] print_constraints: VDAC: at 1800 mV

[    0.156311] print_constraints: VAUX1: at 1800 mV

[    0.157714] print_constraints: VAUX2: at 3300 mV

[    0.159118] print_constraints: VAUX33: at 3300 mV

[    0.160522] print_constraints: VMMC: at 3300 mV

[    0.161010] tps65910 3-002d: No interrupt support, no core IRQ

[    0.161987] Advanced Linux Sound Architecture Driver Version 1.0.24.

[    0.163238] cfg80211: Calling CRDA to update world regulatory domain

[    0.164367] Switching to clocksource gp timer

[    0.181457] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)

[    0.181610] musb-hdrc musb-hdrc.0: dma type: dma-cppi41

[    0.181915] MUSB0 controller's USBSS revision = 4ea20800

[    0.181915] musb0: Enabled SW babble control

[    0.182495] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using PIO, IRQ 18

[    0.182647] musb-hdrc musb-hdrc.1: dma type: dma-cppi41

[    0.182922] MUSB1 controller's USBSS revision = 4ea20800

[    0.182952] musb1: Enabled SW babble control

[    0.183105] musb-hdrc musb-hdrc.1: MUSB HDRC host driver

[    0.183166] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1

[    0.183288] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    0.183288] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    0.183319] usb usb1: Product: MUSB HDRC host driver

[    0.183319] usb usb1: Manufacturer: Linux 3.2.0-00351-gb80917e-dirty musb-hcd

[    0.183319] usb usb1: SerialNumber: musb-hdrc.1

[    0.184143] hub 1-0:1.0: USB hub found

[    0.184173] hub 1-0:1.0: 1 port detected

[    0.184844] musb-hdrc musb-hdrc.1: USB OTG mode controller at e083e800 using PIO, IRQ 19

[    0.185241] NET: Registered protocol family 2

[    0.185394] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.185668] TCP established hash table entries: 16384 (order: 5, 131072 bytes)

[    0.185943] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)

[    0.186096] TCP: Hash tables configured (established 16384 bind 16384)

[    0.186096] TCP reno registered

[    0.186126] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.186126] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.186309] NET: Registered protocol family 1

[    0.186553] RPC: Registered named UNIX socket transport module.

[    0.186584] RPC: Registered udp transport module.

[    0.186584] RPC: Registered tcp transport module.

[    0.186584] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.186798] NetWinder Floating Point Emulator V0.97 (double precision)

[    0.204559] VFS: Disk quotas dquot_6.5.2

[    0.204620] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.205108] msgmni has been set to 998

[    0.205902] io scheduler noop registered

[    0.205932] io scheduler deadline registered

[    0.205993] io scheduler cfq registered (default)

[    0.206848] _regulator_get: tps6116x supply vlcd not found, using dummy regulator

[    0.209808] tps6116x tps6116x: registered backlight controller

[    0.210266] DA8XX FB - no options passed

[    0.210388] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 1024x768 panel

[    0.215820] DA8XX FB: 1024 x 768 16 bpp

[    0.217620] DA8XX FB: 1024 x 768 16 bpp

[    0.226409] Console: switching to colour frame buffer device 128x48

[    0.236236] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    0.238098] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0

[    1.006896] console [ttyO0] enabled

[    1.011230] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1

[    1.019104] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2

[    1.026977] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3

[    1.034790] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4

[    1.042633] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5

[    1.059875] brd: module loaded

[    1.067962] loop: module loaded

[    1.071411] i2c-core: driver [tsl2550] using legacy suspend method

[    1.077911] i2c-core: driver [tsl2550] using legacy resume method

[    1.084350] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write

[    1.097198] MitySOM-335x: Part Number = 3354-HX-X38-RI

[    1.102569] MitySOM-335x Frantec AEC: factory_config_callback

[    1.109283] No SPI NOR Flash found.

[    1.112945] Configuring 512MB NAND device

[    1.117858] omap-gpmc omap-gpmc: GPMC revision 6.0

[    1.122894] Registering NAND on CS0

[    1.129241] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes)

[    1.134826] Creating 1 MTD partitions on "spi_flash":

[    1.140136] 0x000000000000-0x000000800000 : "NOR User Defined"

[    1.148254] omap2-nand driver initializing

[    1.152862] ONFI flash detected

[    1.156311] ONFI param page 0 valid

[    1.159973] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP)

[    1.168365] Creating 8 MTD partitions on "omap2-nand.0":

[    1.173950] 0x000000000000-0x000000040000 : "SPL"

[    1.180419] 0x000000040000-0x000000080000 : "SPL.backup1"

[    1.187347] 0x000000080000-0x0000000c0000 : "SPL.backup2"

[    1.194305] 0x0000000c0000-0x000000100000 : "SPL.backup3"

[    1.201293] 0x000000100000-0x000000300000 : "U-Boot"

[    1.208221] 0x000000300000-0x000000340000 : "U-Boot Env"

[    1.215148] 0x000000340000-0x000000840000 : "Kernel"

[    1.222686] 0x000000840000-0x000020000000 : "File System"

[    1.332366] usb 1-1: new full-speed USB device number 2 using musb-hdrc

[    1.340850] OneNAND driver initializing

[    1.347473] CAN device driver interface

[    1.351501] CAN bus driver for Bosch D_CAN controller 1.0

[    1.357910] d_can d_can.1: device registered (irq=55, irq_obj=56)

[    1.415039] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6

[    1.421539] davinci_mdio davinci_mdio.0: detected phy mask fffffff3

[    1.429382] davinci_mdio.0: probed

[    1.432952] davinci_mdio davinci_mdio.0: phy[2]: device 0:02, driver Micrel KSZ9031 Gigabit PHY

[    1.442077] davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver Micrel KSZ9031 Gigabit PHY

[    1.451599] usbcore: registered new interface driver cdc_ether

[    1.457885] usbcore: registered new interface driver cdc_subset

[    1.464111] Initializing USB Mass Storage driver...

[    1.469451] usbcore: registered new interface driver usb-storage

[    1.475769] USB Mass Storage support registered.

[    1.481170] mousedev: PS/2 mouse device common for all mice

[    1.490264] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0

[    1.503295] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0

[    1.511352] i2c /dev entries driver

[    1.515655] usb 1-1: New USB device found, idVendor=0451, idProduct=2036

[    1.522674] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0

[    1.530151] usb 1-1: Product: General Purpose USB Hub

[    1.535888] Linux media interface: v0.10

[    1.540130] Linux video capture interface: v2.00

[    1.545288] usbcore: registered new interface driver uvcvideo

[    1.551300] USB Video Class driver (1.1.1)

[    1.557006] hub 1-1:1.0: USB hub found

[    1.561035] hub 1-1:1.0: 3 ports detected

[    1.567749] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[    1.576202] cpuidle: using governor ladder

[    1.580963] cpuidle: using governor menu

[    1.587921] usbcore: registered new interface driver usbhid

[    1.593750] usbhid: USB HID core driver

[    1.598602] usbcore: registered new interface driver snd-usb-audio

[    1.618804] ALSA device list:

[    1.621917]   No soundcards found.

[    1.625518] oprofile: hardware counters not available

[    1.630798] oprofile: using timer interrupt.

[    1.635284] Netfilter messages via NETLINK v0.30.

[    1.640258] nf_conntrack version 0.5.0 (7985 buckets, 31940 max)

[    1.647064] ip_tables: (C) 2000-2006 Netfilter Core Team

[    1.652740] TCP cubic registered

[    1.656127] NET: Registered protocol family 17

[    1.660797] can: controller area network core (rev 20090105 abi 8)

[    1.667358] NET: Registered protocol family 29

[    1.672027] can: raw protocol (rev 20090105)

[    1.676513] can: broadcast manager protocol (rev 20090105 t)

[    1.682464] lib80211: common routines for IEEE802.11 drivers

[    1.688415] Registering the dns_resolver key type

[    1.693420] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[    1.701446] ThumbEE CPU extension supported.

[    1.705993] mux: Failed to setup hwmod io irq -22

[    1.711486] Power Management for AM33XX family

[    1.716156] pm: Err (-22) setting core voltage setting

[    1.721740] Trying to load am335x-pm-firmware.bin (60 secs timeout)

[    1.728424] Copied the M3 firmware to UMEM

[    1.732757] Cortex M3 Firmware Version = 0x186

[    1.742919] UBI: attaching mtd8 to ubi0

[    5.832824] UBI: scanning is finished

[    5.852935] UBI: attached mtd8 (name "File System", size 503 MiB) to ubi0

[    5.860076] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes

[    5.867187] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096

[    5.874206] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192

[    5.881408] UBI: good PEBs: 2015, bad PEBs: 0, corrupted PEBs: 0

[    5.887695] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

[    5.895172] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1347087055

[    5.904632] UBI: available PEBs: 0, total reserved PEBs: 2015, PEBs reserved for bad PEB handling: 40

[    5.914459] Detected MACID=68:c9:b:25:48:2e

[    5.919464] UBI: background thread "ubi_bgt0d" started, PID 782

[    5.926147] cpsw: Detected MACID = 68:c9:0b:25:48:30

[    5.935394] tps65910-rtc tps65910-rtc: setting system clock to 2000-01-01 02:23:44 UTC (946693424)

[    6.008209] UBIFS: background thread "ubifs_bgt0_0" started, PID 788

[    6.078216] UBIFS: recovery needed

[    6.598876] UBIFS: recovery completed

[    6.602844] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[    6.609161] UBIFS: LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes

[    6.618743] UBIFS: FS size: 398704640 bytes (380 MiB, 1570 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)

[    6.629119] UBIFS: reserved for root: 0 bytes (0 KiB)

[    6.634399] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 5E0292B7-6E27-4D3C-89BF-AD45A257ABFE, small LPT model

[    6.648559] VFS: Mounted root (ubifs filesystem) on device 0:14.

[    6.655181] Freeing init memory: 244K