Activity
From 05/05/2012 to 06/03/2012
05/31/2012
- 12:54 PM Software Development: RE: Connecting JTAG to Mityarm board
- Raja,
A couple of thoughts come to mind:
1) If your volume is high enough, Critical Link may be able to pre-pro... - 12:16 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Michael,
Thanks for your reply.
I will try with the tera term script file.
We have just SD card available... - 11:01 AM Software Development: RE: Connecting JTAG to Mityarm board
- Another note:
Do you have any other I/O connections for storage such as MMC or USB Host (sticks)? If so you could... - 10:33 AM Software Development: RE: Connecting JTAG to Mityarm board
- Raja
This TI page talks about various ways to flash the NAND (from CCS, etc)
http://processors.wiki.ti.com/index.ph...
05/30/2012
- 05:37 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Alex,
I have also referred the same link provided by you (http://processors.wiki.ti.com/index.php/Linux_Debug_i... - 05:21 PM Software Development: RE: Connecting JTAG to Mityarm board
- Raja,
Typically we load the kernel over either tftp/nfs and write it onto the MityARM-3359 flash memory or boot fr... - 03:46 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Alex,
Do we have any inputs on connecting JTAG to Mityarm board and can be used for flashing?
Alternatively ... - 01:21 PM Software Development: RE: Flashing NAND from SD Card
- Hi Tim,
Thanks. I will wait for your response.
Regards,
Raja. - 01:19 PM Software Development: RE: Flashing NAND from SD Card
- Raja
I am looking in to this... I am suspecting that the u-boot MLO was not configured correctly for the nand flash ... - 01:18 PM Software Development: RE: Flashing NAND from SD Card
- Hi,
Do we have any answer on this.
Thanks,
Raja.
05/29/2012
- 03:21 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Alex,
I am working on to connect the JTAG to the mityarm board.
But having trouble how to proceed with proje... - 09:58 AM Software Development: RE: Flashing NAND from SD Card
- Hi Tim,
I have programmed as per the address mentioned above.
But during booting MLO always looks for u-boot a...
05/24/2012
- 01:33 PM Software Development: RE: Flashing NAND from SD Card
- Raja
The MTD partitions set up in the kernel are also the positions uboot expects
things to be in
Creating 8 MTD p... - 11:47 AM Software Development: RE: Flashing NAND from SD Card
- Hi,
I could load bootloader to NAND and my boot log is as below. Flashed MLO at 0x0 and u-boot.img at 0x40000. u-b...
05/21/2012
- 06:06 PM Software Development: RE: Flashing NAND from SD Card
- Hi Tim,
Do we have any answer on this.
I found one thing interesting from booting sequence of the board.
Below... - 11:05 AM Software Development: RE: Usage of I2C1 to connect external peripheral
- The error you are seeing is from the I2C device not seeing the proper ACK response from the I2C slave device when it ...
- 10:57 AM Software Development: RE: Usage of I2C1 to connect external peripheral
- Hi Mike,
I am coming back to you after long time. we have created setup with the slave connected on mityarm.
At...
05/18/2012
- 12:14 PM Software Development: RE: Flashing NAND from SD Card
- Hi Tim,
I have flashed as mentioned above.
But even now u-boot prompt is not appearing after booting from NAND.
... - 10:42 AM Software Development: RE: Flashing NAND from SD Card
- Raja
Your uboot image is 373252 bytes long
you are only erasing/writing 0x40000, which is 262144 (256k)
try erasin... - 10:08 AM Software Development: RE: Flashing NAND from SD Card
- Hi Tim,
I have followed your instructions and flashed NAND with MLO at 0x20000 and u-boot.img at 0x40000. but the ...
05/17/2012
- 09:54 PM Software Development: RE: Connecting JTAG to Mityarm board
- Raja,
Sorry about the delay but I did want to update the fact that I was able to have the debugger connect to my M... - 06:01 PM Software Development: RE: Flashing NAND from SD Card
- Raja
The uboot spl (MLO) loads from nand at 0x00040000...
nand_spl_load_image: loading 2048 bytes from *0x00040000... - Hi,
1. I have tried flashing NAND through SD boot. I have followed the steps mentioned in AM335x u-boot users guid...
05/16/2012
- 05:42 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Alex,
Thanks for your reply.
I will try with these files.
What are the sys-boot options i have to set whi... - 02:11 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hello Raja,
Attached are both a gel file and a ccxml file that hopefully will get you going. The gel file has been... - 01:21 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Raja -
Sorry for the delay in getting back to you on this. We are working this now and will have an answer for... - 11:53 AM Software Development: RE: Connecting JTAG to Mityarm board
- Hi,
Do we have some inputs on this topic please?
Thanks,
Raja.
05/11/2012
- 12:23 PM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Mike,
Yes, I am connecting to MityARM-3359 and not on TI eval board.
So i want to know what .gel file i need... - 10:43 AM Software Development: RE: Connecting JTAG to Mityarm board
- Hi Raja,
Were you successful when you tried connecting the JTAG to the TI eval board?
I am assuming you are c... - Hi,
I have tried connecting JTAG XDS100V2 to the Mityarm evaluation board. Changed the boot options to give first ...
05/07/2012
- 12:01 PM PCB Development: RE: Power Management w/ MityARM
- Mike,
Thanks for your response, it is really helpful to know how the PMIC is connected. I posted a question about... - 11:06 AM PCB Development: RE: Reg. JTAG Reset and SD Card connection
- Hi Salam,
Thanks for the comments.
1. There is a 10K pull down on the JTAG Reset line so that the JTAG interfac...
Hi,
As per the Mity carrier board design
1, the NRST of JTAG connector is permanently low,that means it is always...
Also available in: Atom
Go to top
