Project

General

Profile

Activity

From 07/09/2017 to 08/07/2017

08/03/2017

07:25 PM Software Development: RE: Using EEPROM available on MitySOM-5CSX
We are using kernel version 4.1.22
-Nick
Nicholas Herbert
07:22 PM Software Development: RE: Using EEPROM available on MitySOM-5CSX
What version of the kernel are you using? From our site? Version 3.16?
-Mike
Michael Williamson
06:58 PM Software Development: RE: Using EEPROM available on MitySOM-5CSX
Mike,
I recently picked up this task and haven't been able to see the NOR flash device in the MTD devices list. On...
Nicholas Herbert

07/20/2017

06:09 PM Software Development: RE: I2C Slave Communication Hanging
So I didn't respond right away as you are using verilog and I am more of a VHDL guy, but there is an open drain primi... Michael Williamson
05:43 PM Software Development: RE: I2C Slave Communication Hanging
We appear to have finally discovered the root cause of our issue. We actually had a self-inflicted bug where the SCL ... Jay Petrie

07/19/2017

07:39 PM Software Development: RE: I2C Slave Communication Hanging
Dan,
I've attached 2 scope shots between the Aardvark as master and the ST1633 as slave:
1. A single byte write w...
Jared Kirschner
03:42 PM Software Development: RE: I2C Slave Communication Hanging
Dan,
We'll be conducting investigations this afternoon with both the Linux I2C kernel driver and a bit-bang I2C us...
Jared Kirschner
03:45 AM Software Development: RE: I2C Slave Communication Hanging
Jared,
To me it looks like the scope capture you've shown should be correct and as you've said there shouldn't be ...
Daniel Vincelette

07/18/2017

07:56 PM Software Development: RE: I2C Slave Communication Hanging
Some additional context / correction:
I2C2 and I2C3 are both configured the same way. If you replace "3" with "2" ...
Jared Kirschner
07:33 PM Software Development: RE: I2C Slave Communication Hanging
All,
This is the open drain primitive we are using for the I2C interfaces:
wire w_i2c3_scl_oe, w_i2c3_scl, w_...
Clyde Shappee
05:09 PM Software Development: RE: I2C Slave Communication Hanging
Are you using the open drain primitive in the top level of the FPGA project?
-Mike
Michael Williamson
05:00 PM Software Development: RE: I2C Slave Communication Hanging
I've attached the driver source/header. I'm waiting to hear from the touch controller vendor whether I can share the ... Jared Kirschner
04:50 PM Software Development: RE: I2C Slave Communication Hanging
We are using I2C2 routed through the FPGA fabric (see image "I2C2_Connector.PNG"). It does have pullups to the best o... Jared Kirschner
04:32 PM Software Development: RE: I2C Slave Communication Hanging
Also, Can you share a snippet of the user space code you are using to issue the read request?
Thanks.
-Mike
Michael Williamson
04:15 PM Software Development: RE: I2C Slave Communication Hanging
Which I2C bus are you using? An HPS peripheral connected directly to HPS pins or routed via FPGA fabric?
This alm...
Michael Williamson
02:52 PM Software Development: I2C Slave Communication Hanging
We're experiencing a problem with I2C communications with a slave on address 0x55 on a MitySOM-5CSX, shown in the att... Jared Kirschner

07/13/2017

03:29 PM FPGA Development: RE: I2C Controller
Thank you, this was resolved, turned out to be a problem with our build scripts. Harrison Barclay

07/12/2017

12:06 PM FPGA Development: RE: I2C Controller
Harrison
Whenever you change anything to do with HPS pin assignments, you will need to rebuild the preloader and upd...
Tim Iskander

07/11/2017

05:51 PM FPGA Development: I2C Controller
Hello,
Unsure whether to post this under the software or FPGA topic.
We are transitioning from a mostly working...
Harrison Barclay
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)