Mity CPU Platforms » MitySOM-335x (ARM Cortex-A8 Based Products)

U-Boot SPL 2013.10-g0451b05 (Jun 16 2017 - 11:39:04)

MitySOM335x profile 1 - Model No: 3352-HX-X4A-RC Serial No: 15013530

Critical Link: Error u-boot not compiled with for 1GB nand support. Nand may not function correctly.

Configuring for 1024 MB DDR3 @ 400MHz

Critical Link AM335X Dev Kit -- NAND Page size = 2048k booting from dev 8

reading u-boot.img

reading u-boot.img

U-Boot 2013.10-g0451b05 (Jun 16 2017 - 11:39:04)

AM335X-GP rev 2

I2C:   ready

DRAM:  1 GiB

WARNING: Caches not enabled

Critical Link: Error u-boot not compiled with for 1GB nand support. Nand may not function correctly.

NAND:  Using 2k bch8 layout

ECC Mode = 2 lo = 56/0

1024 MiB

MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1

*** Warning - bad CRC, using default environment

Net:   cpsw:1 is connected to cpsw.  Reconnecting to cpsw

cpsw, usb_ether

Hit any key to stop autoboot:  0

U-Boot# print bootargs

## Error: "bootargs" not defined

U-Boot# run mmc_args

U-Boot# print bootargs

bootargs=console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none

U-Boot# setenv fdtaddr 0x88000000; setenv fdt_high 0xFFFFFFFF; setenv kloadaddr 0x80007fc0

U-Boot# setenv serverip 10.0.102.252

U-Boot# dhcp; tftp $fdtaddr am335x-mitysom.dtb; tftp $kloadaddr zImage; bootz $kloadaddr - $fdtaddr

link up on port 0, speed 1000, full duplex

link up on port 1, speed 1000, full duplex

BOOTP broadcast 1

DHCP client bound to address 10.0.102.156

Using cpsw device

TFTP from server 10.0.102.252; our IP address is 10.0.102.156

Filename 'uImage'.

Load address: 0x82000000

Loading: #################################################################

         #################################################################

         #################################################################

         ########################################

         1.4 MiB/s

done

Bytes transferred = 3447288 (3499f8 hex)

link up on port 0, speed 1000, full duplex

link up on port 1, speed 1000, full duplex

Using cpsw device

TFTP from server 10.0.102.252; our IP address is 10.0.102.156

Filename 'am335x-mitysom.dtb'.

Load address: 0x88000000

Loading: ###

         1.4 MiB/s

done

Bytes transferred = 37210 (915a hex)

link up on port 0, speed 1000, full duplex

link up on port 1, speed 1000, full duplex

Using cpsw device

TFTP from server 10.0.102.252; our IP address is 10.0.102.156

Filename 'zImage'.

Load address: 0x80007fc0

Loading: #################################################################

         #################################################################

         #################################################################

         ################################################

         1.4 MiB/s

done

Bytes transferred = 3560808 (365568 hex)

Kernel image @ 0x80007fc0 [ 0x000000 - 0x365568 ]

## Flattened Device Tree blob at 88000000

   Booting using the fdt blob at 0x88000000

   Using Device Tree in place at 88000000, end 8800c159

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Initializing cgroup subsys cpuset

[    0.000000] Initializing cgroup subsys cpu

[    0.000000] Initializing cgroup subsys cpuacct

[    0.000000] Linux version 4.1.6-ga7e397a (jhaller@jhaller-VirtualBox) (gcc version 4.8.3 20140401 (prerelease) (Linaro GCC 4.8-2014.04) ) #1 Mon Jun 19 11:50:02 EDT 2017

[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine model: Critical Link MitySOM-335x

[    0.000000] cma: Reserved 24 MiB at 0xbe000000

[    0.000000] Memory policy: Data cache writeback

[    0.000000] CPU: All CPU(s) started in SVC mode.

[    0.000000] AM335X ES2.1 (neon )

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259922

[    0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none

[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Memory: 993680K/1046528K available (6567K kernel code, 533K rwdata, 2312K rodata, 328K init, 8201K bss, 28272K reserved, 24576K cma-reserved, 243712K highmem)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)

[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

[    0.000000]       .text : 0xc0008000 - 0xc08b3f7c   (8880 kB)

[    0.000000]       .init : 0xc08b4000 - 0xc0906000   ( 328 kB)

[    0.000000]       .data : 0xc0906000 - 0xc098b558   ( 534 kB)

[    0.000000]        .bss : 0xc098e000 - 0xc11906f0   (8202 kB)

[    0.000000] Running RCU self tests

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[    0.000000] OMAP clockevent source: timer2 at 24000000 Hz

[    0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns

[    0.000044] clocksource timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns

[    0.000088] OMAP clocksource: timer1 at 24000000 Hz

[    0.000793] Console: colour dummy device 80x30

[    0.000844] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar

[    0.000854] ... MAX_LOCKDEP_SUBCLASSES:  8

[    0.000863] ... MAX_LOCK_DEPTH:          48

[    0.000872] ... MAX_LOCKDEP_KEYS:        8191

[    0.000879] ... CLASSHASH_SIZE:          4096

[    0.000887] ... MAX_LOCKDEP_ENTRIES:     32768

[    0.000895] ... MAX_LOCKDEP_CHAINS:      65536

[    0.000904] ... CHAINHASH_SIZE:          32768

[    0.000912]  memory used by lock dependency info: 5167 kB

[    0.000921]  per task-struct memory footprint: 1152 bytes

[    0.000955] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)

[    0.088396] pid_max: default: 32768 minimum: 301

[    0.088651] Security Framework initialized

[    0.088786] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.088805] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.091134] Initializing cgroup subsys blkio

[    0.091182] Initializing cgroup subsys memory

[    0.091278] Initializing cgroup subsys devices

[    0.091347] Initializing cgroup subsys freezer

[    0.091443] Initializing cgroup subsys perf_event

[    0.091511] CPU: Testing write buffer coherency: ok

[    0.092709] Setting up static identity map for 0x80008200 - 0x80008270

[    0.097563] devtmpfs: initialized

[    0.136666] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[    0.189337] omap_hwmod: tptc0 using broken dt data from edma

[    0.189923] omap_hwmod: tptc1 using broken dt data from edma

[    0.190510] omap_hwmod: tptc2 using broken dt data from edma

[    0.200700] omap_hwmod: debugss: _wait_target_disable failed

[    0.230716] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[    0.233807] pinctrl core: initialized pinctrl subsystem

[    0.238944] NET: Registered protocol family 16

[    0.244278] DMA: preallocated 256 KiB pool for atomic coherent allocations

[    0.246413] cpuidle: using governor ladder

[    0.246445] cpuidle: using governor menu

[    0.257307] OMAP GPIO hardware version 0.1

[    0.283581] omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_default, deferring probe

[    0.288822] No ATAGs?

[    0.288854] hw-breakpoint: debug architecture 0x4 unsupported.

[    0.291939] omap4_sram_init:Unable to allocate sram needed to handle errata I688

[    0.291965] omap4_sram_init:Unable to get sram pool needed to handle errata I688

[    0.336640] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver

[    0.343973] SCSI subsystem initialized

[    0.345612] usbcore: registered new interface driver usbfs

[    0.345791] usbcore: registered new interface driver hub

[    0.345958] usbcore: registered new device driver usb

[    0.346942] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe

[    0.347056] omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c1_pins, deferring probe

[    0.347143] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe

[    0.347462] pps_core: LinuxPPS API ver. 1 registered

[    0.347475] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

[    0.347535] PTP clock support registered

[    0.349826] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400

[    0.352775] Switched to clocksource timer1

[    0.386304] NET: Registered protocol family 2

[    0.388128] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

[    0.388434] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)

[    0.392051] TCP: Hash tables configured (established 8192 bind 8192)

[    0.392288] UDP hash table entries: 512 (order: 3, 40960 bytes)

[    0.392916] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)

[    0.394282] NET: Registered protocol family 1

[    0.395919] RPC: Registered named UNIX socket transport module.

[    0.395944] RPC: Registered udp transport module.

[    0.395955] RPC: Registered tcp transport module.

[    0.395966] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.398074] CPU PMU: Failed to parse /pmu/interrupt-affinity[0]

[    0.398213] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available

[    0.402945] futex hash table entries: 256 (order: 1, 11264 bytes)

[    0.403224] audit: initializing netlink subsys (disabled)

[    0.403489] audit: type=2000 audit(0.400:1): initialized

[    0.408084] VFS: Disk quotas dquot_6.6.0

[    0.408210] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.410370] NFS: Registering the id_resolver key type

[    0.410715] Key type id_resolver registered

[    0.410730] Key type id_legacy registered

[    0.410922] jffs2: version 2.2. (NAND) (SUMMARY)  ? 2001-2006 Red Hat, Inc.

[    0.418828] NET: Registered protocol family 38

[    0.419201] bounce: pool size: 64 pages

[    0.419294] io scheduler noop registered

[    0.419318] io scheduler deadline registered

[    0.419365] io scheduler cfq registered (default)

[    0.421947] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568

[    0.424996] backlight supply power not found, using dummy regulator

[    0.429394] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    0.435786] omap_uart 44e09000.serial: no wakeirq for uart0

[    0.436401] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 155, base_baud = 3000000) is a OMAP UART0

[    1.193508] console [ttyO0] enabled

[    1.199323] omap_uart 481a6000.serial: no wakeirq for uart3

[    1.205651] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 156, base_baud = 3000000) is a OMAP UART3

[    1.216841] omap_uart 481a8000.serial: no wakeirq for uart4

[    1.223156] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 157, base_baud = 3000000) is a OMAP UART4

[    1.236536] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20

[    1.244130] [drm] Initialized drm 1.1.0 20060810

[    1.250004] panel panel: pins are not configured

[    1.260996] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

[    1.268008] [drm] No driver support for vblank timestamp query.

[    1.328617] Console: switching to colour frame buffer device 100x30

[    1.340513] tilcdc 4830e000.lcdc: fb0:  frame buffer device

[    1.346377] tilcdc 4830e000.lcdc: registered panic notifier

[    1.352310] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0

[    1.387321] brd: module loaded

[    1.407333] loop: module loaded

[    1.414168] mtdoops: mtd device (mtddev=name/number) must be supplied

[    1.432597] usbcore: registered new interface driver asix

[    1.438539] usbcore: registered new interface driver ax88179_178a

[    1.445073] usbcore: registered new interface driver cdc_ether

[    1.451344] usbcore: registered new interface driver smsc95xx

[    1.457513] usbcore: registered new interface driver net1080

[    1.463595] usbcore: registered new interface driver cdc_subset

[    1.469909] usbcore: registered new interface driver zaurus

[    1.476008] usbcore: registered new interface driver cdc_ncm

[    1.482573] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    1.489457] ehci-omap: OMAP-EHCI Host Controller driver

[    1.495386] usbcore: registered new interface driver cdc_wdm

[    1.501543] usbcore: registered new interface driver usb-storage

[    1.509884] mousedev: PS/2 mouse device common for all mice

[    1.518331] i2c /dev entries driver

[    1.525562] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[    1.535435] omap_hsmmc 48060000.mmc: Got CD GPIO

[    1.540337] omap_hsmmc 48060000.mmc: Got WP GPIO

[    1.584281] ledtrig-cpu: registered to indicate activity on CPUs

[    1.591252] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2

[    1.606144] omap-sham 53100000.sham: hw accel on OMAP rev 4.3

[    1.619688] usbcore: registered new interface driver usbhid

[    1.625590] usbhid: USB HID core driver

[    1.630653]  remoteproc0: wkup_m3 is available

[    1.635387]  remoteproc0: Note: remoteproc is still under development and considered experimental.

[    1.644764]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.

[    1.656953] oprofile: using arm/armv7

[    1.661670] Initializing XFRM netlink socket

[    1.666418] NET: Registered protocol family 17

[    1.671152] NET: Registered protocol family 15

[    1.676289] Key type dns_resolver registered

[    1.681399] omap_voltage_late_init: Voltage driver support not added

[    1.688125] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize

[    1.696606] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize

[    1.706614] ThumbEE CPU extension supported.

[    1.711109] SmartReflex Class3 initialized

[    1.716792]  remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2

[    1.725861]  remoteproc0: failed to load am335x-pm-firmware.elf

[    1.740046] omap-gpmc 50000000.gpmc: GPMC revision 6.0

[    1.745703] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000

[    1.753453] omap-gpmc 50000000.gpmc: cannot request GPMC CS 0

[    1.759476] omap-gpmc 50000000.gpmc: failed to probe DT children

[    1.767763] omap-gpmc: probe of 50000000.gpmc failed with error -16

[    1.779099] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz

[    1.786962] mmc0: new high speed SDHC card at address 1234

[    1.796312] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 400 kHz

[    1.803543] mmcblk0: mmc0:1234 SA04G 3.67 GiB

[    1.815226]  mmcblk0: p1 p2 p3

[    1.824121] tps65910 2-002d: No interrupt support, no core IRQ

[    1.873765] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz

[    1.880260] backlight supply power not found, using dummy regulator

[    1.952863] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6

[    1.959251] davinci_mdio 4a101000.mdio: detected phy mask fffffffd

[    1.969490] libphy: 4a101000.mdio: probed

[    1.973776] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver unknown

[    1.983784] cpsw 4a100000.ethernet: Detected MACID = ec:24:b8:5d:ee:a5

[    1.994361] hctosys: unable to open rtc device (rtc0)

[    1.999658] sr_init: No PMIC hook to init smartreflex

[    2.005287] sr_init: platform driver register failed for SR

[    2.034233] vbat: disabling

[    2.038507] backlight supply power not found, using dummy regulator

[    2.060187] kjournald starting.  Commit interval 5 seconds

[    2.069459] EXT3-fs (mmcblk0p2): using internal journal

[    2.074995] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode

[    2.082330] VFS: Mounted root (ext3 filesystem) on device 179:2.

[    2.093434] devtmpfs: mounted

[    2.097178] Freeing unused kernel memory: 328K (c08b4000 - c0906000)

INIT: version 2.88 booting

Starting udev

[    3.192258] udevd[91]: starting version 182

[    9.722766] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

[    9.743184] kjournald starting.  Commit interval 5 seconds

[   10.549871] EXT3-fs (mmcblk0p3): using internal journal

[   10.555466] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode

Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory

bootlogd.

[   11.336080] random: dd urandom read with 73 bits of entropy available

Populating dev cache

hwclock: can't open '/dev/misc/rtc': No such file or directory

Mon Mar  6 19:08:00 UTC 2017

hwclock: can't open '/dev/misc/rtc': No such file or directory

INIT: Entering runlevel: 5

Configuring network interfaces... ifup: duplicate interface "usb0"

Starting system message bus: dbus.

Starting Dropbear SSH server: dropbear.

Starting rpcbind daemon...rpcbind: cannot create socket for udp6

rpcbind: cannot create socket for tcp6

done.

creating NFS state directory: done

starting statd: done

Starting HOSTAP Daemon: Configuration file: /etc/hostapd.conf

nl80211: 'nl80211' generic netlink not found

Failed to initialize driver 'nl80211'

rmdir[ctrl_interface]: No such file or directory

/etc/rc5.d/S20hostapd: line 11:   573 Segmentation fault      start-stop-daemon -S -x $DAEMON -- $ARGS

hwclock: can't open '/dev/misc/rtc': No such file or directory

NFS daemon support not enabled in kernel

Starting ntpd: done

Starting syslogd/klogd: done

 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon                       [ ok ]

ioctl FBIOPUT_VSCREENINFO: Invalid argument

No SGX hardware, not starting PVR

Stopping Bootlog daemon: bootlogd.

,--.   ,--.,--.  ,--.            ,---.   ,-----. ,--.   ,--.

|   `.'   |`--',-'  '-.,--. ,--.'   .-' '  .-.  '|   `.'   |

|  |'.'|  |,--.'-.  .-' \  '  / `.  `-. |  | |  ||  |'.'|  |

|  |   |  ||  |  |  |    \   '  .-'    |'  '-'  '|  |   |  |

`--'   `--'`--'  `--'  .-'  /   `-----'  `-----' `--'   `--'

                       `---'

              ,----. ,----. ,-----.,--.   ,--.

              '.-.  |'.-.  ||  .--' \  `.'  /

                .' <   .' < '--. `\  .'    \

              /'-'  |/'-'  |.--'  / /  .'.  \

              `----' `----' `----' '--'   '--'

Critical Link LLC http://support.criticallink.com mitysom-335x /dev/ttyO0

        Linux kernel verison Linux armv7l #1 Mon Jun 19 11:50:02 EDT 2017

Critical Link Linux (sysvinit) 1.6.0 mitysom-335x /dev/ttyO0

mitysom-335x login: root

root@mitysom-335x:~#